How May I Help You?
Remote Controls for CA, OR and WA
Introduction
Resolution Steps
-
Remote Identifier
Experience 4
with VoiceTiVo Series 5
NetflixTiVo Series 5
Champion
(URC2025)Synergy V
(RC-U63CD-R)Synergy V
(RC-U62CD-R)Synergy V
(RC/RT-U62CD)Synergy V
(RC-U62SD)Synergy V
(RT-U60C)PHAZR-5
(UR5U-9000L)OCAP
(URC1056)ENT 8000
ENT 6412
ENT 6208
AllTouch
(AT8550)AllTouch
(AT8400)UR3L-SR4
CLIKR-5
(UR5U-8500L)CLIKR-5
(UR5U-8500)UR5U-8700L
UR5U-8720LUR5U-8400
UR4U-MDVR-CHD2
UR5L-6200L
UR5U-6200
ENT MOTO
UJ4-EXP
UR4-EXP
UR3-EXP
UR3-SR3
UR3-SR2
UR4-DCT
UR4-DSR
UF4-200C
HD uDTA
URC2069
URC2068BC2
DTA Remote
270/271Experience 4 Voice Remote
BlueTooth (BT) and Radio Frequency (RF) remotes do not require a direct line of sight; they can control a DVR anywhere within a radius of approximately 30 feet. A BlueTooth receiver, also known as a BT Dongle is needed for BT remotes unless the TiVo device has a built-in BT receiver (4K models). - Identifying a BT vs. RF remote:
-
If Last is printed in blue, the remote is a BlueTooth Remote
-
If Last is printed in white, the remote is an RF Remote
-
TiVos on Experience 3*:
- TiVo Home | Settings & Messages | Remote, CableCARD, & Devices | Remote Control Setup
*Please be aware that Voice commands cannot be utilized on Experience 3
-
TiVos on Experience 4:
- TiVo Home | left arrow to Menu | Settings | Remote, CableCARD, & Devices | Remote Control Setup
From the Remote Control Setup page, you will be able to select the following options:Set TV power, volume, and mute
- Select the TV brand (use Up, Down, or Ch Up, Ch Down to scroll), and press OK
- Hold down the TV Power and TiVo buttons together, until the light comes on solid (about 5 seconds). Then release both buttons
- Enter the first four-digit code from your list
- Try your TV Power button. If you get no response, try steps 1-3 with the next code on your list
-
If you Can't find the TV code
- Cover the end of the TiVo remote control with your hand
- Hold down both the TiVo and TV Power buttons simultaneously until the light on remote remains lit
- Remove your hand and enter code 0999; the light will flash three times and remain lit
- Press Channel Up once every two seconds to search for the correct code
- Once the TV turns off, press Enter to select the code
- Press TV Power to test the code; if the TV turns on, the remote is programmed
- If the TV does not respond, try these steps again
- Cover the end of the TiVo remote control with your hand
Set TV inputFor cycling through the video inputs of your TV
- Select the TV brand (use Up, Down, or Ch Up, Ch Down to scroll) and press Select
- Hold down the TV Input and TiVo buttons together, until the light comes on solid (about 5 seconds). Then release both buttons
- Enter the first four-digit code from your list
- Try your TV Input button. If you get no response, try steps 1-3 with the next code on your list
-
If you Can't find the TV code
- Cover the end of the TiVo remote control with your hand
- Hold down both the TiVo and TV Input buttons simultaneously until the light on the remote control remains lit
- Remove your hand and enter code 0999; the light will flash three times and remain lit
- Press Channel Up once every two seconds to search for the correct code
- Once the TV changes inputs, press Enter to select the code
- Press TV Input to test the code; if the TV turns on, the remote is programmed
- If the TV does not respond, try these steps again
- Cover the end of the TiVo remote control with your hand
A/V volume, and mute- Select the Audio/Video device brand (use Up, b, or Ch Up, Ch Down to scroll) and press Select
- Hold down the Mute and TiVo buttons together, until the light comes on solid (about 5 seconds). Then release both buttons
- Enter the first four-digit code from your list
- Try your Mute button. If you get no response, try steps 1-3 with the next code on your list
-
If You Can't find the Audio/Video device code
- Cover the end of the TiVo remote control with your hand
- Hold down both the TiVo and Mute buttons simultaneously until the light on the remote control remains lit
- Remove your hand and enter code 0999; the light will flash three times and remain lit
- Press Channel Up once every two seconds to search for the correct code
- Once the volume mutes, press Enter to select the code
- Press TV Input to test the code; if the TV turns on, the remote is programmed
- If the TV does not respond, try these steps again
- Cover the end of the TiVo remote control with your hand
Pair your Remote Control with Your TiVo Box
- If you see this option, your remote can be paired to your TiVo via BT/RF signals. This is only available on 6 tuner and Mini 2 models
- While on this screen, your remote should automatically start pairing within seconds. If not, press the TiVo and Back buttons together until the light at the top of the remote remains lit. Release the buttons and the light will blink yellow/amber while pairing
- When the light stops blinking, press the TiVo button to return to the Home page
- Press the blue Voice (microphone) button on the remote, to confirm the blue Voice icon appears on your TV screen. Your TiVo box is now Voice enabled
-
If this does not work:
- Go to TiVo Home| left arrow to Menu | Setting | Remote, CableCard & Devices | Remote Setup | Pair your remote to your TiVo Box | Reset Remote Control Pairing | Unpair All Remote Controls
- Press the TiVo and Back button to begin re-pairing
- Go to TiVo Home| left arrow to Menu | Setting | Remote, CableCard & Devices | Remote Setup | Pair your remote to your TiVo Box | Reset Remote Control Pairing | Unpair All Remote Controls
The Remote Activity Light indicates when a button on the remote is pressed. When in BT/RF mode, the light is yellow. When in IR mode, the light is red. The TiVo Button takes you to the 'TiVo Home ' page; pressing it a second time takes you to 'My Shows'. If programmed, TV Power turns your TV on/off. Live TV takes you to live TV from the TiVo screens. It also swaps from different tuners so that you can watch something while recording something else. If programmed, Input changes the input source on your TV. Use this button to select the input the TiVo is connected to or to switch to other equipment like a VCR or DVD player. Info allows you to see the channel banner while watching live TV; pressing it again makes it disappear. It also allows you to see the Program Details screen while in the program information screen, giving you additional information about the program. Back returns you to the previous screen, state, or function within the TiVo menus. Exit out of the menu/guide to watch your Live program or recording or close apps
and...
Select the way your widescreen television will display standard (4:3) programming by going to a standard definition channel and pressing this button. Your 4:3 programming can display in Panel (sidebars), Full (Stretch) or Zoom.
The Arrow Buttons are used to navigate the TiVo menus and the TiVo Live Guide. The up and down arrows allow you to scroll through the menus. The right arrow will select a menu option. The left arrow takes you back to the last screen you were on. OK is used in the TiVo menus or the Live Guide to choose menu options or shows to record. Voice command - press and hold the button, and speak naturally into the remote. Release the button when you have finished speaking. Here are some things you can do with voice:
-
Can't decide
what to watch?
- Say "Show
me comedies on tonight" "or "Show action
movies playing at 9 pm" and instantly
see results, avoiding time-consuming and
clunky searches.
- Say "Show
me comedies on tonight" "or "Show action
movies playing at 9 pm" and instantly
see results, avoiding time-consuming and
clunky searches.
-
Ask for a
specific show
- Play the
latest episode of Modern Family
- Play the
latest episode of Modern Family
-
Change channels effortlessly
- Say "channel 2-5-1" or use the channel name
like "ESPN"
- Say "channel 2-5-1" or use the channel name
like "ESPN"
- Instantly set up a OnePass
- "Set up a Onepass for Big Bang Theory"
-
Don't feel
like digging through endless pages of the
Program Guide?
- Say "Show
me what's on tonight" and TiVo will
display shows and movies you might like
to watch based on shows youӶe watched
before
- Say "Show
me what's on tonight" and TiVo will
display shows and movies you might like
to watch based on shows youӶe watched
before
-
Trying to
find something specific but canӴ remember
the name?
- Tell TiVo
to ԓhow me action moviesԠand then dig
further by saying "Just the ones with
Bruce WillisԮ TiVo will get you to what
youӲe looking for faster!
- Tell TiVo
to ԓhow me action moviesԠand then dig
further by saying "Just the ones with
Bruce WillisԮ TiVo will get you to what
youӲe looking for faster!
-
Want to show
your friends something cool?
- Use your
favorite movie quote! Say "Hasta la
vista, baby" into your remote and watch
as "Terminator 2" appears moments later.
- Use your
favorite movie quote! Say "Hasta la
vista, baby" into your remote and watch
as "Terminator 2" appears moments later.
-
Search by
movie or show title, franchise, or genre
- "Doctor
Who", "Breaking Bad", "Back to the
Future"
- "Doctor
Who", "Breaking Bad", "Back to the
Future"
-
Search by
actor, director, or producer
- "Movies
directed by Steven Spielberg" or
"Show me movies
with George Clooney and Julia Roberts"
- "Movies
directed by Steven Spielberg" or
"Show me movies
with George Clooney and Julia Roberts"
- Search for Menu commands or apps
- "Settings",
"My Shows", "Hulu", "show me the
Guide", "Show me action movies on Netflix"
Guide takes you to the TiVo Live Guide or Grid Guide where you can choose programs to watch or record. Pressing it again clears the guide from the screen. If programmed, Volume increases and decreases the volume on your TV or stereo. If programmed, Mute turns off the audio of your TV or stereo. Channel up/down changes the channel on the TiVo and allows you to page up or down while in the TiVo menus. Thumbs Up lets you give shows you like a positive rating. You can give a show up to three thumbs up. These ratings are used by the TiVo to choose programs to record for TiVo Suggestions. Record starts recording the show you are currently watching. Thumbs Down lets you give shows you don't like a negative rating. You can give a show up to three thumbs down. These ratings are used by the TiVo to choose programs to record for TiVo Suggestions. Play will start playing a recorded show from Now Playing. When you are using pause, rewind, fast-forward or slow, pressing Play will resume playing at normal speed. Rewind rewinds a program. Press it up to three times for three speeds. Press it a fourth time to resume playing. When the TiVo is paused, it allows you to go back frame-by-frame. Slow plays a recording or live TV in slow motion. Use in conjunction with FF or REW buttons for frame-by-frame motion. Fast-Forward fast-forwards through a program. Press it up to three times for three speeds. Press it a fourth time to resume playing. When the TiVo is paused, it allows you to advance frame-by-frame. Pause freezes a recorded show or live TV. Pressing it again resumes playing. Instant Replay repeats the last 8 seconds of the program on a recording or live TV. This button also will take TV Listings back 24 hours at a time.
The On Demand button takes you directly to Video On Demand. The NETFLIX button takes you directly to the NETFLIX App. Advance jumps ahead 30 seconds when watching recorded programming. Hold down more than 2 seconds and it will take you to the end the show. If you are watching live (buffered) TV, you can use it to catch up to the live broadcast. Use in conjunction with FF or REW buttons to skip to each 15 minute tick marker.
This button also will take TV Listings forward 24 hours at a time.
A, B, C, D - Special options used throughout TiVo's Interactive Guide for sorting and filtering results. Number buttons allow you to enter channel numbers. Numbers 0, 1, 2, 3, 4, 5, and 6 also take you to shortcuts in the guide while in TiVo central.
Number 0 takes you to the TiVo animation while in TiVo central.
Clear removes the channel banner on live TV or a recorded program. You can also use it to delete programs from My Shows. or
Enter/Last returns you to the last channel the TiVo was tuned to in live TV. If Last is printed in blue, the remote is a BlueTooth Remote.
If Last is printed in white, the remote is a RF Remote
In IR mode, the remote will work with ANY of our TiVos. To enter IR mode:
Press and hold the
+
buttons until the activity indicator on the remote control lights. The remote remains in IR mode until you enter the key combination that puts the remote into BT/ RF mode.
Switching to BT/RF mode (for 6 Tuner TiVos):
Entering BT/RF mode causes a paired remote that is currently operating in IR mode to switch to BT/ RF mode. This procedure has no effect in New Pairing mode or when the remote is unpaired.
To change the remote control from IR mode to BT/RF mode, press and hold the+
buttons until the activity indicator on the remote control lights.
Are you always losing your remote? The TiVo T6 remote uses a remote finder feature to help you locate your missing remote. - On the T6, touch the amber image of the remote control on the front of the DVR:
- On the MG2, the remote finder button is on the back of the DVR:
- When pressed, a
TiVo jingle will play on the remote
- When you find the
remote, press any button to deactivate the
sound, or just wait 15 seconds for it to turn
off automatically
IMPORTANT: The remote must be in BT/ RF mode for this to work
The Global Reset function un-pairs the remote from the paired DVR, then clears any other remote settings, such as IR codes for your television or other A/V device. Use this function to unpair a remote and return it to the out-of-box settings. IMPORTANT: You will need both the paired remote and the DVR to perform a global reset. If your paired remote has been lost or damaged, you will need to use a new remote in IR mode to put the DVR in a pairing state, then pair the new remote to the DVR. For instructions, see To Pair a different remote to your DVR.
- Press and hold the
+
buttons until light on the remote blinks
- Press
three times, then press
- The light on the remote will flash three times if the global reset is successful
TiVo Series 5 Netflix Remote
Overview
- IR mode: In infrared (IR) mode, the remote relies on a direct line of sight to control the DVR via infrared signals. The remote is set in IR mode when you take it out of the box. IR mode does not require the remote to be paired to a specific DVR. In this mode, the remote will work with ANY of our TiVos.
- RF mode: In radio frequency (RF) mode, the remote does not require a direct line of sight. Rather, the remote can control a DVR anywhere within a radius of approximately 30 feet. To enter RF mode, you must pair the remote to a specific DVR
-
New Pairing mode:
The remote control that comes with
your 6 Tuner TiVo is already in New Pairing mode. This pairing mode allows you to pair the
DVR and remote control automatically by pressing any button on the remote control.
- Allow Pairing mode: This pairing mode is for manually adding a new remote control or transferring a remote control from one DVR to another. When you put the remote control in Allow Pairing mode, it will pair with any available 6 Tuner TiVo that is accepting pairing requests within range.
- If the activity indicator flashes red, the remote is sending IR commands to the DVR.
- If the activity indicator flashes amber, the remote is paired and is sending RF commands to the DVR.
This article uses some terms that might be unfamiliar. Read through this list of terms and definitions if you need clarification:Pairing mode: Supports two methods for pairing:
Global Reset: The Global Reset function un-pairs the remote control from the paired DVR and clears any other remote settings, such as IR codes for your TV or other A/V devices.
Remote activity indicator colors
When the remote control is in Allow Pairing mode, the activity indicator (the TiVo logo's antennae on the TiVo button) slowly flashes. When the remote control successfully pairs with a DVR, the activity indicator flashes quickly five times and then stops.
When you press buttons on the remote, the activity indicator flashes different colors to indicate what kind of signal the remote is sending:NOTE: 6 Tuner TiVos can be paired with up to 10 remote controls.
Programming your Remote
- Select the TV brand (use Up, b, or
Ch Up, Ch Down to scroll), and press Select
- Hold down the TV Power and TiVo
buttons together, until the light comes on solid (about 5 seconds).
Then release both buttons.
- Enter the first four-digit code from your
list
- Try your TV Power button. If you get no response, try steps 1-3 with the next code on your list.
-
Cover the end of the TiVo
remote control with your hand
- Hold down both the TiVo
and TV Power buttons simultaneously
until the light on remote remains lit
-
Remove your hand and
enter code 0999; the light will flash three
times and remain lit
-
Press Channel Up once every two seconds to search for the correct code
- Once the TV turns off,
press Enter to select the code
- Press TV Power to
test the code; if the TV turns on, the remote is programmed
- Once the TV turns off,
press Enter to select the code
- If the TV does not respond, try these steps again
- Select the TV brand (use Up, b, or
Ch Up, Ch Down to scroll) and press Select
- Hold down the TV Input and TiVo
buttons together, until the light comes on solid (about 5 seconds).
Then release both buttons
- Enter the first four-digit code from your
list
- Try your TV Input button. If you get no response, try steps 1-3 with the next code on your list.
-
Cover the end of the
TiVo remote control with your hand
- Hold down both the TiVo
and TV Input buttons simultaneously
until the light on the remote control remains lit
-
Remove your hand and
enter code 0999; the light will flash three
times and remain lit
- Press Channel Up once
every two seconds to
search for the correct code
- Once the TV changes inputs,
press Enter to select the code
- Press TV Input to
test the code; if the TV turns on, the remote is programmed
- Once the TV changes inputs,
press Enter to select the code
- If the TV does not respond, try these steps again
- Select the Audio/Video device brand (use Up,
b, or Ch Up, Ch Down to scroll) and press Select
- Hold down the Mute and TiVo
buttons together, until the light comes on solid (about 5 seconds).
Then release both buttons
- Enter the first four-digit code from your
list
- Try your Mute button. If you get
no response, try steps 1-3 with the next code on your list.
-
Cover the end of the
TiVo remote control with your hand
- Hold down both the TiVo and
Mute buttons simultaneously until the
light on the remote control remains lit
-
Remove your hand and
enter code 0999; the light will flash three
times and remain lit
-
Press Channel Up once every two seconds to search for the correct code
- Once the volume mutes,
press Enter to select the code
- Press TV Input to
test the code; if the TV turns on, the remote is programmed
- Once the volume mutes,
press Enter to select the code
- If the TV does not respond, try these steps again
- Your remote should automatically pair to
the TiVo from this page
- Hold your Series 5 Remote no more
than 3 feet from the TiVo
- The Amber light on top should
steadily blink until done
- If the remote wont pair, perform a global reset and try the above steps again
For TiVos on Experience 3:TiVo Central | Settings & Messages | Settings | Remote, CableCARD, & Devices | Remote Control Setup
TiVos on Experience 4:
TiVo Home | left arrow to Menu | Settings | Remote, CableCARD, & Devices | Remote Control Setup
From the Remote Control Setup page, you will be able to select the following options:
Set TV power, volume, and mute
If you can't find the TV code
Set TV input
For cycling through the video inputs of your TV
If you can't find the TV code
A/V volume, and mute
If You can't find the Audio/Video device code
Remote Control Pairing
If you see this option, your remote can be paired to your TiVo via RF signals. This is only available on 6 tuner and Mini 2 models.
Using the Remote
- On the T6, touch the amber image of the remote control on the front of the
DVR:
- On the MG2, the remote finder button is
on the back of the DVR:
- When pressed, a TiVo jingle will play on the
remote
- When you find the remote, press any button to
deactivate the sound, or just wait 15 seconds for it to turn off automatically
Batteries
Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment.When the batteries become too weak to operate the remote control properly, the TiVo will start to be unresponsive to remote commands. When this happens, install 2 new "AA" size batteries.
Button Descriptions
The Remote Activity Light indicates when a button on the remote is pressed. When in RF mode, the light is yellow. When in IR mode, the light is red. The TiVo Button takes you to 'TiVo Central'; pressing it a second time takes you to 'My Shows'. If programmed, TV Power turns your TV on/off. Live TV takes you to live TV from the TiVo screens. It also swaps from different tuners so that you can watch something while recording something else. Back returns you to the previous screen, state, or function within the TiVo menus. If programmed, Input changes the input source on your TV. Use this button to select the input the TiVo is connected to or to switch to other equipment like a VCR or DVD player. Info allows you to see the channel banner while watching live TV; pressing it again makes it disappear. It also allows you to see the Program Details screen while in the program information screen, giving you additional information about the program. The Arrow Buttons are used to navigate the TiVo menus and the TiVo Live Guide. The up and down arrows allow you to scroll through the menus. The right arrow will select a menu option. The left arrow takes you back to the last screen you were on. Select is used in the TiVo menus or the Live Guide to choose menu options or shows to record. The Magnifying Glass button takes you directly to TiVo's search page. Exit out of the menu/guide to watch your Live program or recording
and...
Select the way your widescreen television will display standard (4:3) programming by going to a standard definition channel and pressing this button. Your 4:3 programming can display in Panel (sidebars), Full (Stretch) or Zoom.
Guide takes you to the TiVo Live Guide or Grid Guide where you can choose programs to watch or record. Pressing it again clears the guide from the screen. If programmed, Volume increases and decreases the volume on your TV or stereo. If programmed, Mute turns off the audio of your TV or stereo. Channel up/down changes the channel on the TiVo and allows you to page up or down while in the TiVo menus. Thumbs Up lets you give shows you like a positive rating. You can give a show up to three thumbs up. These ratings are used by the TiVo to choose programs to record for TiVo Suggestions. Record starts recording the show you are currently watching. Thumbs Down lets you give shows you don't like a negative rating. You can give a show up to three thumbs down. These ratings are used by the TiVo to choose programs to record for TiVo Suggestions. Play will start playing a recorded show from Now Playing. When you are using pause, rewind, fast-forward or slow, pressing Play will resume playing at normal speed. Rewind rewinds a program. Press it up to three times for three speeds. Press it a fourth time to resume playing. When the TiVo is paused, it allows you to go back frame-by-frame. Slow plays a recording or live TV in slow motion. Use in conjunction with FF or REW buttons for frame-by-frame motion. Fast-Forward fast-forwards through a program. Press it up to three times for three speeds. Press it a fourth time to resume playing. When the TiVo is paused, it allows you to advance frame-by-frame. Pause freezes a recorded show or live TV. Pressing it again resumes playing. Instant Replay repeats the last 8 seconds of the program on a recording or live TV. This button also will take TV Listings back 24 hours at a time.
The On Demand button takes you directly to Video On Demand. The NETFLIX button takes you directly to the NETFLIX App. Advance jumps ahead 30 seconds when watching recorded programming. Hold down more than 2 seconds and it will take you to the end the show. If you are watching live (buffered) TV, you can use it to catch up to the live broadcast. Use in conjunction with FF or REW buttons to skip to each 15 minute tick marker.
This button also will take TV Listings forward 24 hours at a time.
A, B, C, D - Special options used throughout TiVo's Interactive Guide for sorting and filtering results. Number buttons allow you to enter channel numbers. Numbers 1, 2, 3, 4, 5, and 6 also take you to shortcuts in the guide while in TiVo central.
Number 0 takes you to the TiVo animation while in TiVo central.
Clear removes the channel banner on live TV or a recorded program. You can also use it to delete programs from My Shows. Enter/Last returns you to the last channel the TiVo was tuned to in live TV. Switching Modes (IR / RF)
In IR mode, the remote will work with ANY of our TiVos.To enter IR mode:
Press and hold the
+
buttons until the activity indicator on the remote control lights. The remote remains in IR mode until you enter the key combination that puts the remote into RF mode.
Switching to RF mode (for 6 Tuner TiVos):
Entering RF mode causes a paired remote that is currently operating in IR mode to switch to RF mode. This procedure has no effect in New Pairing mode or when the remote is unpaired.
To change the remote control from IR mode to RF mode, press and hold the+
buttons until the activity indicator on the remote control lights.
Using the Remote Finder feature (TiVo T6, Pace MG2 Only)
Are you always losing your remote? The TiVo T6 remote uses a remote finder feature to help you locate your missing remote.IMPORTANT: The remote must be in RF mode for this to work
Performing a Global Reset
- Press and hold the
+
buttons until light on the remote blinks
- Press
three times, then press
- The light on the remote will flash three times if the global reset is successful
The Global Reset function un-pairs the remote from the paired DVR, then clears any other remote settings, such as IR codes for your television or other A/V device. Use this function to unpair a remote and return it to the out-of-box settings.
IMPORTANT: You will need both the paired remote and the DVR to perform a global reset. If your paired remote has been lost or damaged, you will need to use a new remote in IR mode to put the DVR in a pairing state, then pair the new remote to the DVR. For instructions, see To Pair a different remote to your DVR.
TiVo Series 5 Remote
Overview
- IR mode: In infrared (IR) mode, the remote relies on a direct line of sight to control the DVR via infrared signals. The remote is set in IR mode when you take it out of the box. IR mode does not require the remote to be paired to a specific DVR. In this mode, the remote works with ANY of our TiVos.
- RF mode: In radio frequency (RF) mode, the remote does not require a direct line of sight. Rather, the remote can control a DVR anywhere within a radius of approximately 30 feet. To enter RF mode, you must pair the remote to a specific DVR
-
New Pairing
mode:
The remote control that comes with
your 6 Tuner TiVo is already in New Pairing
mode. This pairing mode allows you to pair the
DVR and remote control automatically by pressing
any button on the remote control.
- Allow Pairing mode: This pairing mode is for manually adding a new remote control or transferring a remote control from one DVR to another. When you put the remote control in Allow Pairing mode, it will pair with any available 6 Tuner TiVo that is accepting pairing requests within range.
- If the activity indicator flashes red, the remote is sending IR commands to the DVR.
- If the activity indicator flashes amber, the remote is paired and is sending RF commands to the DVR.
This article uses some terms that might be unfamiliar. Read through this list of terms and definitions if you need clarification:Pairing mode: Supports two methods for pairing:
Global Reset: The Global Reset function un-pairs the remote control from the paired DVR and clears any other remote settings, such as IR codes for your TV or other A/V devices.
Remote activity indicator colors
When the remote control is in Allow Pairing mode, the activity indicator (the TiVo logo's antennae on the TiVo button) slowly flashes. When the remote control successfully pairs with a DVR, the activity indicator flashes quickly five times and then stops.
When you press buttons on the remote, the activity indicator flashes different colors to indicate what kind of signal the remote is sending:NOTE: 6 Tuner TiVos can be paired with up to 10 remote controls.
Programming your Remote
- Select the TV
brand (use Up, b, or Ch Up,
Ch Down to scroll), and press Select
- Hold down the TV
Power and TiVo buttons
together, until the light comes on solid
(about 5 seconds). Then release both
buttons.
- Enter the first
four-digit code from your list
- Try your TV
Power button. If you get no response,
try steps 1-3 with the next code on your
list.
-
Cover
the end of the TiVo remote
control with your hand
- Hold down
both the TiVo
and TV Power buttons
simultaneously until
the light on
remote remains lit
-
Remove
your hand and enter code 0999;
the light will flash three
times and remain lit
-
Press Channel Up color="#800000">once every two seconds to search for the correct code
- Once
the TV turns off,
press Enter to select
the code
- Press TV
Power to test the
code; if the TV turns on, the remote
is programmed
- Once
the TV turns off,
press Enter to select
the code
- If the TV does not respond, try these steps again
- Select the TV
brand (use Up, b, or Ch Up,
Ch Down to scroll) and press Select
- Hold down the TV
Input and TiVo buttons
together, until the light comes on solid
(about 5 seconds). Then release both buttons
- Enter the first
four-digit code from your list
- Try your TV
Input button. If you get no response,
try steps 1-3 with the next code on your
list.
-
Cover
the end of the TiVo remote
control with your hand
- Hold down both
the TiVo and TV
Input buttons simultaneously
until the light on the
remote control remains lit
-
Remove
your hand and enter code 0999;
the light will flash three
times and remain lit
- Press Channel
Up color="#800000">once
every two seconds to search for
the correct code
- Once
the TV changes inputs,
press Enter to select
the code
- Press TV
Input to test the code;
if the TV turns on, the remote is
programmed
- Once
the TV changes inputs,
press Enter to select
the code
- If the TV does not respond, try these steps again
- Select the
Audio/Video device brand (use Up, b,
or Ch Up, Ch Down to scroll)
and press Select
- Hold down the Mute
and TiVo buttons together, until the
light comes on solid (about 5 seconds). Then
release both buttons
- Enter the first
four-digit code from your list
- Try your Mute
button. If you get no response, try steps
1-3 with the next code on your list.
-
Cover
the end of the TiVo remote control
with your hand
- Hold down
both the TiVo and Mute
buttons simultaneously
until the light on the
remote control remains lit
-
Remove
your hand and enter code 0999;
the light will flash three
times and remain lit
-
Press Channel Up color="#800000"> once every two seconds to search for the correct code
color="#800000">
- Once
the volume mutes,
press Enter to select
the code
- Press TV
Input to test the code;
if the TV turns on, the remote is
programmed
- Once
the volume mutes,
press Enter to select
the code
- If the TV does not respond, try these steps again
- Your remote
should automatically pair to the TiVo from
this page
- Hold your
Series 5 Remote no more than 3 feet from the
TiVo
- The Amber light
on top should steadily blink until done
- Go to Live TV
and test the remote
- For Tivo Experience 3 if the
remote wont pair, perform a global
reset and try the above steps again
- For Tivo Experience
4, if the remote won't pair, follow these
steps:
- Go to TiVo
Central | left arrow to Menu | Setting |
Remote, CableCard & Devices | Remote
Setup | Pair your remote to your TiVo
Box | Reset Remote Control Pairing |
Unpair All Remote Controls
- Press the TiVo
and Back button
TiVos on Experience 3:TiVo Central | Settings & Messages | Settings | Remote, CableCARD, & Devices | Remote Control Setup
TiVos with Experience 4
Go to TiVo Home | left arrow to Menu | Settings | Remote, CableCard & Devices | Remote Control Setup
From the Remote Control Setup page, you will be able to select the following options:
Set TV power, volume, and mute
If you can't find the TV code
Set TV input
For cycling through the video inputs of your TVIf you can't find the TV code
A/V volume, and mute
If you can't find the Audio/Video device code
Remote Control Pairing - Pair Your Remote to Your TiVo Box
If you see this option, your remote can be paired to your TiVo via RF signals. This is only available on 6 tuner and Mini 2 models.
Using the TiVo Series 5 Remote
- On the T6,
touch the amber image of the remote
control on the front of the DVR:
- On the MG2,
the remote finder button is on the back of
the DVR:
- When pressed,
a TiVo jingle will play on the remote
- When you find
the remote, press any button to deactivate
the sound, or just wait 15 seconds for it
to turn off automatically
Batteries
Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment.When the batteries become too weak to operate the remote control properly, the TiVo will start to be unresponsive to remote commands. When this happens, install 2 new "AA" size batteries.
Button Descriptions
The Remote Activity Light indicates when a button on the remote is pressed. When in RF mode, the light is yellow. When in IR mode, the light is red. The TiVo Button takes you to 'TiVo Central'; pressing it a second time takes you to 'Now Playing'. If programmed, TV Power turns your TV on/off. Live TV takes you to live TV from the TiVo screens. It also swaps from different tuners so that you can watch something while recording something else. Back returns you to the previous screen, state, or function within the TiVo menus. If programmed, Input changes the input source on your TV. Use this button to select the input the TiVo is connected to or to switch to other equipment like a VCR or DVD player. Info allows you to see the channel banner while watching live TV; pressing it again makes it disappear. It also allows you to see the Program Details screen while in the program information screen, giving you additional information about the program. The Arrow Buttons are used to navigate the TiVo menus and the TiVo Live Guide. The up and down arrows allow you to scroll through the menus. The right arrow will select a menu option. The left arrow takes you back to the last screen you were on. Select is used in the TiVo menus or the Live Guide to choose menu options or shows to record. Select the way your widescreen television will display standard (4:3) programming by going to a standard definition channel and pressing this button. Your 4:3 programming can display in Panel (sidebars), Full (Stretch) or Zoom. and...
Exit out of the menu/guide to watch your Live program or recording
Guide takes you to the TiVo Live Guide or Grid Guide where you can choose programs to watch or record. Pressing it again clears the guide from the screen. If programmed, Volume increases and decreases the volume on your TV or stereo. If programmed, Mute turns off the audio of your TV or stereo. Channel up/down changes the channel on the TiVo and allows you to page up or down while in the TiVo menus. Thumbs Up lets you give shows you like a positive rating. You can give a show up to three thumbs up. These ratings are used by the TiVo to choose programs to record for TiVo Suggestions. Record starts recording the show you are currently watching. Thumbs Down lets you give shows you don't like a negative rating. You can give a show up to three thumbs down. These ratings are used by the TiVo to choose programs to record for TiVo Suggestions. Play will start playing a recorded show from Now Playing. When you are using pause, rewind, fast-forward or slow, pressing Play will resume playing at normal speed. Rewind rewinds a program. Press it up to three times for three speeds. Press it a fourth time to resume playing. When the TiVo is paused, it allows you to go back frame-by-frame. Slow plays a recording or live TV in slow motion. Use in conjunction with FF or REW buttons for frame-by-frame motion. Fast-Forward fast-forwards through a program. Press it up to three times for three speeds. Press it a fourth time to resume playing. When the TiVo is paused, it allows you to advance frame-by-frame. Pause freezes a recorded show or live TV. Pressing it again resumes playing. Instant Replay repeats the last 8 seconds of the program on a recording or live TV. This button also will take TV Listings back 24 hours at a time.
or
The VOD button takes you directly to Video On Demand. Advance jumps ahead 30 seconds when watching recorded programming. Hold down more than 2 seconds and it will take you to the end the show. If you are watching live (buffered) TV, you can use it to catch up to the live broadcast. Use in conjunction with FF or REW buttons to skip to each 15 minute tick marker.
This button also will take TV Listings forward 24 hours at a time.
A, B, C, D - Special options used throughout TiVo's Interactive Guide for sorting and filtering results. Number buttons allow you to enter channel numbers. Numbers 1, 2, 3, 4, 5, and 6 also take you to shortcuts in the guide while in TiVo central.
Number 0 takes you to the TiVo animation while in TiVo central.
Clear removes the channel banner on live TV or a recorded program. You can also use it to delete programs from My Shows. Enter/Last returns you to the last channel the TiVo was tuned to in live TV. Switching Modes (IR / RF)
In IR mode, the remote will work with ANY of our TiVos.To enter IR mode:
Press and hold the
+
buttons until the light on the remote turns on. The remote remains in IR mode until you enter the key combination that puts the remote into RF mode.
Switching to RF mode (for 6 Tuner TiVos):
Entering RF mode causes a paired remote that is currently operating in IR mode to switch to RF mode. This procedure has no effect in New Pairing mode or when the remote is unpaired.
To change the remote control from IR mode to RF mode, press and hold the+
buttons until the activity indicator on the remote control lights.
Using the Remote Finder feature (TiVo T6 AND Pace MG2 Only)
Are you always losing your remote? The TiVo T6 remote uses a remote finder feature to help you locate your missing remote.IMPORTANT: The remote must be in RF mode for this to work
Performing a Global Reset
- Press and
hold the
+
buttons until the activity indicator lights up
- Press
three times, then press
- The activity indicator will flash three times if the global reset is successful
The Global Reset function un-pairs the remote from the paired DVR, then clears any other remote settings, such as IR codes for your television or other A/V device. Use this function to unpair a remote and return it to the out-of-box settings.
IMPORTANT: You will need both the paired remote and the DVR to perform a global reset. If your paired remote has been lost or damaged, you will need to use a new remote in IR mode to put the DVR in a pairing state, then pair the new remote to the DVR. For instructions, see To Pair a different remote to your DVR.
Series 4 TiVo
Programming the Series 4 Remote
- Find the brand name of your TV from the
list provided.
- Hold down the TV Power and TiVo buttons together, until the red light comes on solid (about 5 seconds). Then release both buttons.
- Enter the first four-digit code from your list.
- Try your TV Power button. If you get no response, try again with the next code on your list.
- Find the brand name of your device from
the list provided.
- Hold down the Mute and TiVo buttons together, until the red light comes on solid (about 5 seconds). Then release both buttons.
- Enter the first four-digit code from your list.
- Try your Mute button. If you get no response, try again with the next code on your list.
- Find the brand name of your TV from the
list provided.
- Hold down the TV Input and TiVo buttons together, until the red light comes on solid (about 5 seconds). Then release both buttons.
- Enter the first four-digit code from your list.
- Try your TV Input button. If you get no response, try again with the next code on your list.
- Cover the end of the TiVo remote control with your hand to block the
I/R signal
- Hold down the TiVo and TV Power buttons together until the light on the remote control remains
on+
- Remove your hand from the end of the TiVo remote control
- Enter code 0999 - After entering this code, the remote control light will flash 3 times and remain on
- Press Channel Up once every two seconds; this will test hundreds of codes, one by
one
-
Important: Going any faster than this may skip over a code that works
-
Important: Going any faster than this may skip over a code that works
- When pressing Channel Up turns off the TV, press Enter to select the
code
- Press TV Power button to test the code; if the TV turns on, the remote has been successfully programmed
- Once the TiVo remote cycles through all available codes, the remote light will go out, indicating all codes have been
tried
- If this happened, or if the TV does not respond to the code selected, repeat these steps to make sure the code was not skipped over by cycling through the codes too fast
Go to:TiVo Central | Settings & Messages | Settings | Remote, CableCARD, & Devices | Remote Control Setup
TV Power, volume, and mute
A/V volume and mute
TV Input
Using Code Search When You Can't find the Code
Resetting the TiVo remote
- Cover the end of the TiVo remote control with your hand
- Press the TiVo and the TV Power buttons simultaneously until the light at the end of the remote comes
on
- Press Thumbs Down 3 times, followed by Enter. The remote light should go out. If the light does not go out, repeat this step
NOTE: If the incorrect button is pressed, press Clear to start over.
Button Functions
The Remote Activity Light indicates when a button on the remote is pressed. The TiVo Button takes you to 'TiVo Central'; pressing it a second time takes you to 'Now Playing'. If programmed, TV Power turns your TV on/off. Live TV takes you to live TV from the TiVo screens. It also swaps from different tuners so that you can watch something while recording something else. If programmed, Input changes the input source on your TV. Use this button to select the input the TiVo is connected to or to switch to other equipment like a VCR or DVD player. Display or Info allows you to see the channel banner while watching live TV; pressing it again makes it disappear. It also allows you to see the Program Details screen while in the program information screen, giving you additional information about the program. The Arrow Buttons are used to navigate the TiVo menus and the TiVo Live Guide. The up and down arrows allow you to scroll through the menus. The right arrow will select a menu option. The left arrow takes you back to the last screen you were on. Select is used in the TiVo menus or the Live Guide to choose menu options or shows to record. Select the way your widescreen television will display standard (4:3) programming by going to a standard definition channel and pressing this button. Your 4:3 programming can display in Panel (sidebars), Full (Stretch) or Zoom. Guide takes you to the TiVo Live Guide or Grid Guide where you can choose programs to watch or record. Pressing it again clears the guide from the screen. If programmed, Volume increases and decreases the volume on your TV or stereo. If programmed, Mute turns off the audio of your TV or stereo. Channel up/down changes the channel on the TiVo and allows you to page up or down while in the TiVo menus. Thumb Up lets you give shows you like a positive rating. You can give a show up to three thumbs up. These ratings are used by the TiVo to choose programs to record for TiVo Suggestions. Record starts recording the show you are currently watching. Thumbs Down lets you give shows you don't like a negative rating. You can give a show up to three thumbs down. These ratings are used by the TiVo to choose programs to record for TiVo Suggestions. Play will start playing a recorded show from Now Playing. When you are using pause, rewind, fast-forward or slow, pressing Play will resume playing at normal speed. Rewind rewinds a program. Press it up to three times for three speeds. Press it a fourth time to resume playing. When the TiVo is paused, it allows you to go back frame-by-frame. Slow plays a recording or live TV in slow motion. Use in conjunction with FF or REW buttons for frame-by-frame motion. Fast-Forward fast-forwards through a program. Press it up to three times for three speeds. Press it a fourth time to resume playing. When the TiVo is paused, it allows you to advance frame-by-frame. Pause freezes a recorded show or live TV. Pressing it again resumes playing. Instant Replay repeats the last 8 seconds of the program on a recording or live TV. This button also will take TV Listings back 24 hours at a time.
or
The VOD button takes you directly to RCN Video On Demand. Advance jumps ahead 30 seconds when watching recorded programming. Hold down more than 2 seconds and it will take you to the end the show. If you are watching live (buffered) TV, you can use it to catch up to the live broadcast. Use in conjunction with FF or REW buttons to skip to each 15 minute tick marker.
This button also will take TV Listings forward 24 hours at a time.
A, B, C, D - Special options used throughout TiVo's Interactive Guide Number buttons allow you to enter channel numbers. Numbers 1, 2, 3, 4, 5, and 6 also take you to shortcuts in the guide while in TiVo central.
Number 0 takes you to the TiVo animation while in TiVo central.
Clear removes the channel banner on live TV or a recorded program. You can also use it to delete programs from My Shows. Enter/Last returns you to the last channel the TiVo was tuned to in live TV. TiVo 'Slide' Remote
The 'Slide' remote uses the same programming instructions as above.Champion (URC2025)
This remote is programmed by default to command Motorola/Pace/Arris and Scientific Atlanta/Cisco converters. No programming to these converters is necessary.
Program Remote Using the Popular Brands Method
- Turn on the equipment you wish to program (TV,
DVD, AUX, or AUD)
- Press the device key (TV, AUDIO, DVD) the LED will light off and on again
- Press and hold SETUP until the mode key blinks
twice
- Find your device and brand from the chart below and note the DIGIT key assigned to your brand.
Using your number buttons, press and hold down the DIGIT key for your device/brand
TV DVD/Blu Ray Audio Device Digit Insignia / Dynex Insignia / Dynex Bose 1 LG / Zenith LG Denon 2 Mitsubishi Panasonic LG 3 Panasonic Philips / Magnavox Onkyo 4 Philips / Magnavox RCA Panasonic 5 Samsung Samsung Philips 6 Sharp Sharp Pioneer 7 Sony Sony Samsung 8 Toshiba Sylvania Sony 9 Vizio Toshiba Yamaha 0 - Press POWER to confirm the remote now controls the device. If the device does not turn off, repeat steps 2-4 using the next code for your device
If your brand does not appear in the brand chart, perform setup using either the Four-Digit Code Programming or Code Search
Four-Digit Code Programming Method
- Turn on the equipment you wish to program (TV,
DVD, AUDIO)
- Press and release the device key (TV,
DVD, AUDIO)
- Press and hold SETUP until the device key (TV,
DVD, AUDIO) blinks once, and then twice
- Enter 1st code for your Audio Device brand from the code list.
Using TV key
Using AUDIO key
Using DVD key
or
- Press POWER to confirm the remote now controls the device. If the device does not turn off, repeat steps 2-4 using the next code for your device
Auto Search Method
- Turn on the equipment you wish to operate
- Press and hold SETUP until TV, DVD, or AUDIO blinks once, then twice
- Press the the device key you wish to program (TV,
DVD, AUDIO). The mode key will stay lit
-
Press and hold
down the OK/SELECT
key. Let go of the OK/SELECT key when your device turns off
- Press the POWER button to turn the device back on
If the four-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct code number for your equipment by the following steps:
Code Number Readback
- Press the device key you wish to program (TV,
DVD, AUDIO). The mode key will stay lit
- Press and hold SETUP until the device key (TV,
DVD, AUDIO) blinks twice
- Press 9-9-0 on the remote. The mode key
(TV, DVD, AUDIO) will blink twice
- To view first digit in your 4 digit code, press 1 and count the number of times the mode key blinks
back
-
Press 2 and count the number of times the mode key blinks back. this is your
second digit
-
Press 3 and count the number of times the mode key blinks back. this is your third
digit
-
Press 4 and count the number of times the mode key blinks back. this is your
fourth digit
-
NOTE: If a code digit is “0” the red light will not blink
-
NOTE: If a code digit is “0” the red light will not blink
-
Press 2 and count the number of times the mode key blinks back. this is your
second digit
- Write your device's brand & setup code for future reference
To identify the 4-digit setup code for your device, follow these steps:
Programming the System On/Off Button
- Press [CBL]
- Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
- Press [TV]
- Press [DVD] (if adding)
- Press [AUD] (if adding)
- Press [AUX] (if adding)
- Press [CH▲] to save the power commands you stored. The [CBL] button will blink twice to confirm
The System on/off button can send out up to three power on/off commands for the devices you programmed into the remote control
Volume Control
- Press and hold SETUP until the mode key blinks
twice
- Press VOLUME + key
- Press the mode key that corresponds to the device you use for volume
controls
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : CBL TV : TV DVD : TV AUD : AUD AUX : AUX
If you wish to store another device's volume control in CBL mode, use the following steps
To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [device] with [CBL] in step 3
Video Input Button
- The button can change the input source of the TV (Input 1, Input 2, Aux, Game, Video 1, Video 2, etc) - this is the preferred default
- .. or, the button can change the input source of an audio
device's input (CD, DVD, TV SOUND, etc.)
- Press and hold
SETUP until the mode key blinks twice
- Press VIDEO INPUT
- Press the device key that corresponds to the device you use for volume controls (TV or AUDIO)
This button can change the input source of your TV or other electronic device while in any mode.
To program this button, follow the steps below:
Your remote's WATCH CABLE Button
- Press and hold SETUP until the mode key blinks
twice
- Press WATCH CABLE
- In the order you want the devices to turn on, press the mode key that corresponds to the device ONCE AT A TIME.
For example:Press ,
and the converter and TV will turn on/off in that order and puts the remote in CABLE mode.
Press ,
,
and the converter, TV, and Audio Device will turn on/off in that order and puts the remote in CABLE mode.
Press ,
,
and the TV, converter, and Audio Device will turn on/off in that order and puts the remote in CABLE mode.
Once you have programmed the remote to operate your electronic devices, you can press the WATCH CABLE button to turn your converter and TV on and off with one button press. You can also program the WATCH CABLE button to turn off/on additional devices and/or tune your TV to it's correct output channel.
IMPORTANT:
You must first program ALL devices on your Champion (URC2025) for the WATCH CABLE button to work correctly.
Follow these steps if you wish to use an alternate device for volume control.
Battery Info
Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment.When the battery is low, the remote control LED blinks 2 times whenever a [device] button is pressed to turn on equipment.
Button Functions
Programming Your Cable Converter
- Turn on your converter
- Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence like below:
- Try code 001, 002, or 003 until the converter turns off
- Press [MUTE]
- If your CABLE converter turns back on, press [OK] to lock in the code
- The mode (power) buttons will blink 3 times and go out
- The mode (power) buttons will blink 3 times and go out
- If your CABLE converter does not turn back on, repeat steps 3 and 4 until you can turn your CABLE converter off and on
- If your CABLE converter turns back on, press [OK] to lock in the code
- Write your CABLE brand & setup code down for future reference
Programming Other Devices
- Turn on your device
- Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
- From the Setup Code list below, locate and enter the 3-digit code for your brand. If multiple codes are listed, you may have to enter several 3-digit codes until your device turns off
- If you cannot find your code, you can use Point and Press Programming
- If you cannot find your code, you can use Point and Press Programming
- Press [MUTE]
- If your device turns back on, press [OK] to lock in the code
- The mode (power) buttons will blink 3 times and go out
- The mode (power) buttons will blink 3 times and go out
- Use your device key (AUDIO, DVD, VCR, TV) to power the device back on If your device does not turn back on, repeat steps using a different setup code
- Try specific commands for your device, like:
- TV - [VOL UP], [VOL DOWN] and [MUTE]
- VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
- DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
- Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
- If your device does not work for specific commands, repeat steps using a different setup code
- Write your device brand & setup code for future reference
Point and Press Programming
- Turn on your device
- Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
- Press and hold the [CH +] button until the TV turns off
- Every time the buttons light in a sequence, the remote is trying a different code. It may take seconds or several minutes for the remote to find the proper code for your device
- Please be patient, and be ready to release the [CH +] button when the device turns off
- Press [MUTE]
- If your TV turns back on, press [OK] to lock in the code. The mode (power) buttons will blink 3 times and go out
- If your TV does not run back on, try pressing [CH -] one step at a time until that device turns back on. Each time you press the [CH -] button, the power/mode buttons will start blinking in reverse sequence:
- Once you have found the proper code, press [OK] to lock in the code
- Try specific commands for your device, like:
- TV - [VOL UP], [VOL DOWN] and [MUTE]
- VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
- DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
- Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
- If your device does not work for specific commands, repeat steps above
Code Number Readback
- Press [device key], then [OK] - hold both down until the [device key] button lights up under finger
- Press [INFO]. The illuminated button will “blink back” the code number, with a 1-second interval between each digit of the code
- The remote will display the number "0" as the mode buttons ALL quickly flash a few times (CBL, TV, VCR, DVD, AUDIO)
- Example: TV Code is 3-0-1
- [TV], [TV], [TV]
- (one-second pause)
- All device keys flash
- (one-second pause)
- [TV]
To identify the 3-digit setup code for your device, follow these steps:
Programming Volume Control
- Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
- Press [VOL ], then [CBL]. The [CBL] button will blink and go out
- Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
- Press [VOL ], then [TV]. The [CBL] button will blink and go out
By default, your remote defaults to your TV volume control (unless you are in AUDIO mode)
To control volume commands through your CONVERTER in the remote's CABLE mode:
To control volume / mute back through your TV in the remote's CABLE mode:Installing / Replacing Batteries
Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment
When the batteries become too weak to operate the remote control properly, the mode keys will become dim or not illuminate at all during use. When this happens, install 2 new "AA" size batteries
Your remote control has Memory Guard, which eliminates reprogramming after battery changes
General Reset
- Press [OK], then [CBL] together until the [CBL] button lights up (under your finger)
- Press [1]
- The [CBL] button will blink 3 times and go out. All codes will now be cleared. Start programming your remote over again, as needed
The remote can be reset to its factory default settings if needed
Synergy V (RC-U62CD-R)
Programming Your Cable Converter
- Turn on your converter
- Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence like below:
- Try code 001, 002, or 003 until the converter turns off
- Press [MUTE]
- If your converter turns back on, press [OK] to lock in the code
- The mode (power) buttons will blink 3 times and go out
- The mode (power) buttons will blink 3 times and go out
- If your CABLE converter does not turn back on, repeat steps 3 and 4 until you can turn your CABLE converter off and on
- If your converter turns back on, press [OK] to lock in the code
- Write your CABLE brand & setup code down for future reference
Programming Other Devices
- Turn on your device
- Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
- From the Setup Code list below, locate and enter the 3-digit code for your brand. If multiple codes are listed, you may have to enter several 3-digit codes until your device turns off
- If you cannot find your code, you can use Point and Press Programming
- If you cannot find your code, you can use Point and Press Programming
- Press [MUTE]
- If your device turns back on, press [OK] to lock in the code
- The mode (power) buttons will blink 3 times and go out
- The mode (power) buttons will blink 3 times and go out
- Use your device key (AUDIO, DVD, VCR, TV) to power the device back on If your device does not turn back on, repeat steps using a different setup code
- Try specific commands for your device, like:
- TV - [VOL UP], [VOL DOWN] and [MUTE]
- VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
- DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
- Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
- If your device does not work for specific commands, repeat steps using a different setup code
- Write your device brand & setup code for future reference
Point and Press Programming
- Turn on your device
- Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
- Press and hold the [CH +] button until the TV turns off
- Every time the buttons light in a sequence, the remote is trying a different code. It may take seconds or several minutes for the remote to find the proper code for your device
- Please be patient, and be ready to release the [CH +] button when the device turns off
- Press [MUTE]
- If your TV turns back on, press [OK] to lock in the code. The mode (power) buttons will blink 3 times and go out
- If your TV does not run back on, try pressing [CH -] one step at a time until that device turns back on. Each time you press the [CH -] button, the power/mode buttons will start blinking in reverse sequence:
- If your TV turns back on, press [OK] to lock in the code. The mode (power) buttons will blink 3 times and go out
- Once you have found the proper code, press [OK] to lock in the code
- Try specific commands for your device, like:
- TV - [VOL UP], [VOL DOWN] and [MUTE]
- VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
- DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
- Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
- If your device does not work for specific commands, repeat steps above
Programming Volume Control
- Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
- Press [VOL ], then [CBL]. The [CBL] button will blink and go out
- Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
- Press [VOL ], then [TV]. The [CBL] button will blink and go out
By default, your remote defaults to your TV volume control (unless you are in AUDIO mode)
To control volume commands through your CONVERTER in the remote's CABLE mode:
To control volume / mute back through your TV in the remote's CABLE mode:Installing / Replacing Batteries
Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment
When the batteries become too weak to operate the remote control properly, the mode keys will become dim or not illuminate at all during use. When this happens, install 2 new "AA" size batteries
Your remote control has Memory Guard, which eliminates reprogramming after battery changes
General Reset
- Press [OK], then [CBL] together until the [CBL] button lights up (under your finger)
- Press [1]
- The [CBL] button will blink 3 times and go out. All codes will now be cleared. Start programming your remote over again, as needed
- If the [CBL] button DID NOT blink 3 times and go out, follow the alternate procedure below.
- Press [OK], then [CBL] together until the [CBL] button lights up (under your finger)
- Press [0]
- The [CBL] button will blink 3 times and go out. All codes will now be cleared. Start programming your remote over again, as needed
The remote can be reset to its factory default settings if needed
Synergy V (Model RT-U62CD / RC-U62CD)
Programming Your Cable Converter
- Turn on your converter
- Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence like below:
- Try code 001, 002, or 003 until the converter turns off
- Press [MUTE]
- If your converter turns back on, press [OK] to lock in the code
- The mode (power) buttons will blink 3 times and go out
- The mode (power) buttons will blink 3 times and go out
- If your CABLE converter does not turn back on, repeat steps 3 and 4 until you can turn your CABLE converter off and on
- If your converter turns back on, press [OK] to lock in the code
- Write your CABLE brand & setup code down for future reference
Programming Other Devices
- Turn on your device
- Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
- From the Setup Code list below, locate and enter the 3-digit code for your brand. If multiple codes are listed, you may have to enter several 3-digit codes until your device turns off
- If you cannot find your code, you can use Point and Press Programming
- If you cannot find your code, you can use Point and Press Programming
- Press [MUTE]
- If your device turns back on, press [OK] to lock in the code
- The mode (power) buttons will blink 3 times and go out
- The mode (power) buttons will blink 3 times and go out
- Use your device key (AUDIO, DVD, VCR, TV) to power the device back on If your device does not turn back on, repeat steps using a different setup code
- Try specific commands for your device, like:
- TV - [VOL UP], [VOL DOWN] and [MUTE]
- VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
- DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
- Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
- If your device does not work for specific commands, repeat steps using a different setup code
- Write your device brand & setup code for future reference
Point and Press Programming
- Turn on your device
- Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
- Press and hold the [CH +] button until the TV turns off
- Every time the buttons light in a sequence, the remote is trying a different code. It may take seconds or several minutes for the remote to find the proper code for your device
- Please be patient, and be ready to release the [CH +] button when the device turns off
- Press [MUTE]
- If your TV turns back on, press [OK] to lock in the code. The mode (power) buttons will blink 3 times and go out
- If your TV does not run back on, try pressing [CH -] one step at a time until that device turns back on. Each time you press the [CH -] button, the power/mode buttons will start blinking in reverse sequence:
- If your TV turns back on, press [OK] to lock in the code. The mode (power) buttons will blink 3 times and go out
- Once you have found the proper code, press [OK] to lock in the code
- Try specific commands for your device, like:
- TV - [VOL UP], [VOL DOWN] and [MUTE]
- VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
- DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
- Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
- If your device does not work for specific commands, repeat steps above
Code Number Readback
- Press your device key, then [SEL/OK] - hold both down until the device button lights up under your finger
- Press [INFO] The illuminated button will “blink back” the code number, with a 1-second interval between each digit of the code
-
The number 0 will blink 10 times
- For example: Code 405:
- blinks 4 times
- 1 second
- Blinks 10 times
- 1 second
- Blinks 5 times
-
The number 0 will blink 10 times
To identify the 3-digit setup code for your device, follow these steps:
Programming Volume Control
- Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
- Press [VOL ], then [CBL]. The [CBL] button will blink and go out
- Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
- Press [VOL ], then [TV]. The [CBL] button will blink and go out
By default, your remote defaults to your TV volume control (unless you are in AUDIO mode)
To control volume commands through your CONVERTER in the remote's CABLE mode:
To control volume / mute back through your TV in the remote's CABLE mode:Installing / Replacing Batteries
Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment
When the batteries become too weak to operate the remote control properly, the mode keys will become dim or not illuminate at all during use. When this happens, install 2 new "AA" size batteries
Your remote control has Memory Guard, which eliminates reprogramming after battery changes
General Reset
- Press [OK], then [CBL] together until the [CBL] button lights up (under your finger)
- Press [1]
- The [CBL] button will blink 3 times and go out. All codes will now be cleared. Start programming your remote over again, as needed
- If the [CBL] button DID NOT blink 3 times and go out, follow the alternate procedure below.
- Press [OK], then [CBL] together until the [CBL] button lights up (under your finger)
- Press [0]
- The [CBL] button will blink 3 times and go out. All codes will now be cleared. Start programming your remote over again, as needed
The remote can be reset to its factory default settings if needed
Program Remote Using the Popular Brands Method
- Turn on the equipment you wish to program (TV, DVD, AUX, or AUD)
- Point the remote at the device and press and hold the [OK/SEL] and TV buttons together for 3 seconds While holding the device key (TV, AUD, DVD, AUX) the LED will light off and on again
- Begin to press the numbers keys, one at a time, starting with 1, then 2, 3, etc until the device turns off
# TV Audio DVD AUX 0 SANYO ROTEL HITACHI BOSE 1 SONY DENON SONY HP 2 SAMSUNG YAMAHA PHILIPS APPLE / iPod 3 LG MARANTZ SAMSUNG APPLE / iPod 4 TOSHIBA SONY PHILIPS MAGNAVOX MICROSOFT / XBOX 5 PANASONIC INTEGRA PANASONIC SONY / PS2 6 PHILIPS HARMAN KARDON LG LUTRON 7 HITACHI PIONEER JVC X-10 8 SHARP ONKYO DENON X-10 9 VIZIO LEXICON PIONEER MICROSOFT / XBOX
- If your brand does not appear in the brand chart, perform setup using either DIRECT CODE ENTRY or CODE SEARCH
- Press the device button (TV, DVD, AUX, or AUD) to save the code
- The device button LED will blink twice to confirm the code is stored
Three-Digit Code Programming Method
- Turn on the equipment you wish to program (TV, DVD, AUX, or AUD)
- Press and hold the device key (TV, AUD, DVD, AUX) and the [OK/SEL] button down together for 3 seconds until the device key stays lit
- The device key (TV, AUD, DVD, AUX) will stay lit for 30 seconds. The next step must be entered while the LED is on
- The device key (TV, AUD, DVD, AUX) will stay lit for 30 seconds. The next step must be entered while the LED is on
- Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables
- Try the first three-digit number and wait one second for the equipment to turn off. If it doesn't, try the next three-digit number, and so on, until the device turns off
Using TV key
Using AUD key
Using DVD key
Using AUX key
- Try the first three-digit number and wait one second for the equipment to turn off. If it doesn't, try the next three-digit number, and so on, until the device turns off
- Press [POWER] to turn the device
back on
- If the device does not turn back on, repeat steps 1-5
- Press the device key (TV, AUD, DVD, AUX) again. The device LED will blink twice to confirm that the code has been stored
Auto Search Method
- Turn on the equipment you wish to operate
- Press the device key (TV, AUD, DVD, AUX) and [OK/SEL] simultaneously for 3 seconds. The device key (TV, AUD, DVD, AUX) will turn on indicating that it's ready to be programmed
- Press [CH UP] or [CH DOWN] button and release. Do this every one second or keep the button pressed down. A new code will be entered one at a time Release the [CH UP] or [CH DOWN] button when the device turns off
- Press [POWER] to turn the device back on
- Try all of the functions of the remote control. If the buttons do not work as they should, repeat steps again
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:
Code Number Readback
- Press the device key (TV, AUD, DVD, AUX) and [OK/SEL] simultaneously for 3 seconds. The device key (TV, AUD, DVD, AUX) will turn on
- Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
- Each digit is separated by 1 second. Ten blinks is equal to the number 0
- For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Volume Control
- CBL : CBL
- TV : TV
- DVD : TV
- AUD : AUD
- AUX : AUX
- Press [CBL] and [OK/SEL] simultaneously for 3 seconds
- [CBL] will light on for 30 seconds. The next step must be entered while the LED is on
- Press [VOL UP]
- Press [TV]. [TV] will blink twice to confirm the programming
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
If you wish to store the TV volume control in CBL mode, use the following stepsTo restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [TV] with [CBL] in step 4
Battery Info
Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment.
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.Resetting The Remote
- Hold [CBL] and [REC] until the mode lights flash in order, should take roughly 5 seconds
- Reset does not cause the remote to lose its ability to control the converter
Programming TV using Code Entry Method
- Turn on the TV
- Press [SEL/OK] and [MUTE] together until the indicator light illuminates
- Enter in the code for your TV:
- Enter EVERY code listed until your TV turns off
- Test the TV by pressing [MUTE]. If the TV turns back on, the programming was successful
- If your TV turns back on, press [SEL/OK] to lock in the code
- If the TV Does not turn on, enter the next code listed until the TV turns back on and press [SEL/OK] to lock in the code
Programming TV Using Point and Press Method
- Turn on the TV
- Press [SEL/OK] and [MUTE] together until the indicator light illuminates
- Press and hold [CH UP] until the TV turns off
- As soon as the TV turns off, release [CH UP]
- Test the TV by pressing [MUTE]
- If the TV turns back on, the programming was successful. Press [SEL/OK] to lock in the code
- If the TV Does not turn on, press [CH DOWN] until the TV turns back on and press [SEL/OK] to lock in the code
- If the TV turns back on, the programming was successful. Press [SEL/OK] to lock in the code
TV Code Readback
- Press [TV POWER] and [SEL/OK] together until the indicator light illuminates
- Press [INFO] to identify your TV setup code
- The indicator light blinks back the code numbers with a 1-second interval between each digit
- "0" Is indicated by 6 fast blinks
- For example, 0-0-3-5 would blink back as:
- 6 fast blinks
- (one second)
- 6 fast blinks
- (one second)
- 3 slow blinks
- (one second)
- 5 slow blinks
- "0" Is indicated by 6 fast blinks
Programming Volume Control
- Press and [CBL POWER] and [SEL/OK] together until the indicator light illuminates
- Press [VOL UP], then [CBL POWER]. The indicator light will blink and go out
- Press and hold the [CBL POWER] and [SEL/OK] together until the indicator light illuminates
- Press [VOL UP], then [TV POWER]. The indicator light will blink and go out
The default volume control is done through the TVTo program volume control to your Cable Converter:
To control the volume back through the TV:Batteries
Install two (2) new "AA" batteries as indicated by the diagram in the battery compartment.When the indicator light becomes dim or no longer illuminates during use, batteries need to be replaced.
Memory Guard
This remote has Memory guard, which eliminates reprogramming after battery changes.Resetting Your Remote
- Press and [CBL POWER] and [MUTE] together until the indicator light illuminates
- Press [1]. The indicator light will blink and go out
To reset your remote to its default settings:
Cisco Digital Transport Adapter (DTA) Remote Controls 270/271
Printable manuals (271 (HDA-RF 2.2), 270 (HDA-IR 2.2))
Identifying the 270 vs. 271
These remotes are identical.
The model numbers are stamped on the back The 271 (IR/RF model) is listed as HDA-RF 2.2 The 270 is listed as HDA-IR 2.2
Auto-Search Programming (recommended)
- Turn on your TV
- Point the remote control at the DTA
- Press and hold the Prog button for three seconds until the LED turns on
- Press and hold the [CH+] button search for codes
- A new code transmits every 1.5 seconds, and the LED will blink for each one
- A new code transmits every 1.5 seconds, and the LED will blink for each one
- When your TV turns off, the remote control has found a valid code
- Press the TV button to store the code
- To test, press TV Power
Manual Programming Method
- Find your device codes in the manual
- Turn on your TV
- Point the remote control at the DTA
- Press and hold the Prog button for three seconds until the LED turns on
- Press and hold the [TV] button. The LED will blink once and remain on
- Enter the code for your brand
- If the code is valid, the LED will blink twice and the code will be retained
- If the code is invalid, the LED will blink three times, and remain in programming mode. Try another code on the list
- Press the TV button to test. the TV should turn off
Pairing the 271 Remote - RF Mode
- Press and hold the [Prog] button for three seconds until the LED turns on
- Press the [Info] key
- The LED on the remote will blink slowly indicating that the device is in pairing mode
- Enter the 3 digits the DTA shows on-screen The DTA will acknowledge the 3 digits entered was correct
Unpairing the 271 Remote
- Press and hold the Prog button for three seconds until the LED turns on
- Press 9, 8, 7
- The LED will blink 2 times quickly
Volume Control
- Press and hold the [Prog] button for three seconds until the LED turns on
- Press the [Vol+] button
- Press and hold the [Prog] button for three seconds until the LED turns on
- Press the [Vol-] button
By default the remote controls the volume and mute on the DTA, not the TV
To control the volume and mute on the TV:
To control the volume and mute back to the DTA:
Programming Your Cable Converter
Your remote control is pre-programmed to operate the Scientific Atlanta and Motorola Digital / DVR set-top terminals. Therefore, no further programming of your Cable devices is necessary.Programming Other Devices
- Turn on your device
- Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
- From the Setup Code list below, locate and enter the 3-digit code for your brand. If multiple codes are listed, you may have to enter several 3-digit codes until your device turns off
- If you cannot find your code, you can use Point and Press Programming
- If you cannot find your code, you can use Point and Press Programming
- Press [MUTE]
- If your device turns back on, press [OK] to lock in the code
- The mode (power) buttons will blink 3 times and go out
- The mode (power) buttons will blink 3 times and go out
- Use your device key (MOT, AUDIO, VIDEO, TV, S-A) to power the device back on If your device does not turn back on, repeat steps using a different setup code
- Try specific commands for your device, like:
- TV - [VOL UP], [VOL DOWN] and [MUTE]
- VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
- DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
- Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
- If your device does not work for specific commands, repeat steps using a different setup code
- Write your device brand & setup code for future reference
Point and Press Programming
- Turn on your device
- Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
- Press and hold the [CH +] button until the TV turns off
- Every time the buttons light in a sequence, the remote is trying a different code. It may take seconds or several minutes for the remote to find the proper code for your device
- Please be patient, and be ready to release the [CH +] button when the device turns off
- Press [MUTE]
- If your TV turns back on, press [OK] to lock in the code. The mode (power) buttons will blink 3 times and go out
- If your TV does not run back on, try pressing [CH -] one step at a time until that device turns back on. Each time you press the [CH -] button, the power/mode buttons will start blinking in reverse sequence:
- If your TV turns back on, press [OK] to lock in the code. The mode (power) buttons will blink 3 times and go out
- Once you have found the proper code, press [OK] to lock in the code
- Try specific commands for your device, like:
- TV - [VOL UP], [VOL DOWN] and [MUTE]
- VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
- DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
- Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
- If your device does not work for specific commands, repeat steps above
Code Number Readback
- Press your device key (Audio, Video, or TV), then [SEL/OK] - hold both down until the device button lights up under your finger
- Press [INFO] The illuminated button will “blink back” the code number, with a 1-second interval between each digit of the code
-
The number 0 will blink 10 times
- For example: Code 405:
- blinks 4 times
- 1 second
- Blinks 10 times
- 1 second
- Blinks 5 times
-
The number 0 will blink 10 times
To identify the 3-digit setup code for your device, follow these steps:
Buttton Functions
Installing / Replacing Batteries
Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment
When the batteries become too weak to operate the remote control properly, the mode keys will become dim or not illuminate at all during use. When this happens, install 2 new "AA" size batteries
Your remote control has Memory Guard, which eliminates reprogramming after battery changes
General Reset
- Press [S-A] or [MOT], then [SEL/OK] together until the [S-A] or [MOT] button lights up (under your finger)
- Press [0]
- The [S-A] or [MOT] button will blink 3 times and go out
- All codes will now be CLEARED. Start programming your Synergy V over again, as needed
Programming Devices into the URC1056 Remote
-
For control of a Combo device (for example, a TV/VCR combo), skip this section and perform the instructions on Setting Up a Combo Unit
-
These instructions assume you have already selected the proper device code(s)
- Turn on the device
- Press and hold the appropriate device key until it blinks
once
VCR VCR, PVR, DVR or extra DVD Player DVD DVD Player, or extra VCR, TV/VCR Combo or PVR AUD Audio Amplifier, Tuner, or Receiver TV Television CBL Cable Box (Converter) or Satellite Receiver
- Press and hold the SETUP key until it blinks twice
- Enter in the code for the device:
Audio Amplifiers -- >
Audio Receivers -- >
Audio Accessories -- >
DVD Players -- >
DVD Recorders -- >
DVD Combos -- >
DVR/PVR Systems -- >
TVs -- >
DLP TVs -- >
HDTVs -- >
LCD TVs -- >
VCR -- >
The mode keys should then blink twice if the code was accepted.
If the selected mode key emits a long blink, the entry is invalid. Repeat steps 2 through 4 and try entering the same code again.
- Test the device by pressing PWR. If the device responds, the program was
successful
- If the device does not respond, repeat steps 2-4 for other codes (if applicable)
Note:
Setting Up a Combo Unit:
- For a TV/VCR or TV/DVD Combo, turn on your Combo
unit and insert a video cassette (or a
DVD)
- On the remote control, press VCR (or DVD)
once ; it will blink once. Then press and hold SETUP until the VCR key blinks
twice
- Use the Manufacturer’s Codes below to locate the brand name and enter the first four-digit code
TV/DVD Combos controlled by TV -- >
TV/DVD Combos controlled by DVD -- >
TV/VCR Combos controlled by TV -- >
TV/VCR Combos controlled by VCR -- >
TV/VCR/DVD Combos controlled by TV -- >
TV/VCR/DVD Combos controlled by DVD -- >
TV/VCR/DVD Combos controlled by VCR -- >
- If you perform this procedure correctly, the VCR key will blink
twice
NOTE: If the VCR key did not blink twice after entering the codes last digit, repeat steps 2 through 4 and try entering the same code again.
If you’ve located a setup code that works for your combo device (for example, a TV/VCR Combo) and a separate TV code is also listed, you’ll need to program this code into the remote control to access volume control (see “Programming Device Control”)
If you own a combo unit such as a TV/VCR Combo or a TV/DVD Combo, you need to follow special steps to set it up. Perform the following instructions to control a combo device:
Searching for Codes
- Turn on your TV
- On the remote control, press TV once; it will blink once. Then press and hold
SETUP until the TV key blinks twice
- Using the remote keypad, press 9, 9, 1. The mode keys will blink
twice
- Aim the remote control at the TV and press PWR once
NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first
- Press PWR. The TV should turn on, then press
SETUP to lock in the code
- If the TV does not turn on during step 5, then slowly press and release CH- to go back through the codes, then press SETUP when the TV turns on
If your home entertainment device does not respond to the Atlas OCAP 5-Device Remote Control after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code.For example, to search for a code for your TV:
Code Number Read Back:
- On the remote control, press TV once; it will blink once. Then press and hold
SETUP until the TV key blinks twice.
- Enter 9, 9, 0. The TV key will blink twice.
- To view the code for the first digit, press 1 once. Count the number of times the
TV key blinks (e.g., 3 blinks = 3)
NOTE: If a code digit is 0, the selected mode key will not blink.
- Repeat step 3 three more times for the remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit
- To check for other device codes, repeat steps 1 through 4, but substitute the appropriate key (e.g., VCR, DVD, AUD, or CBL) for the device you are checking
If you have set up the Atlas OCAP 5-Device Remote Control by searching for your device code (on the previous page), you may need to find out which four digit code is operating your equipment.
For example, to find out which code is operating your TV:
Channel Control Lock
- On the remote control, press CBL once; it will blink once. Press and hold
SETUP until the CBL key blinks twice
- Enter 9, 7, 3. The CBL key will blink
twice
- Press CH- once. The CBL key will blink four
times
Now the remote control will provide TV and VCR channel-control capabilities while in the TV or VCR mode.
By default, the remote control’s channel-control capabilities are locked to the cable converter. The affected keys* are 1 through 0, CH+, CH-, and LAST. This will guarantee that you do not inadvertently change a channel on your TV or VCR. However, you can deactivate this feature to allow full access to these keys in the TV and VCR modes
*NOTE: This feature does not affect the AUD mode.Unlocking Channel Control
Locking Channel Control to CBL
- On the remote control, press CBL once; it will blink once. Press and hold
SETUP until the CBL key blinks twice
- Enter 9, 7, 3. The CBL key will blink
twice
- Press CH+ once. The CBL key will blink four
times
Now, regardless of what mode you select (except AUD), the channel keys will only change channels on your cable converter
Volume Lock
- Assuming Global Volume Lock is active, select a mode on the remote control that you want to unlock (e.g.,
CBL) and press it once. Next, press and hold SETUP until the device key blinks
twice
- Enter 9, 9, 3. The last-selected device key will blink
twice
- Press VOL- once. The last-selected device key will blink four
times
- Repeat steps 1 through 3 for each device you want volume to be
unlocked
Now, after you select a device that has volume unlocked (e.g., CBL), pressing VOL+, VOL-,or MUTE, will control only that device’s volume. - On the remote control, press and hold SETUP until the last-selected device key blinks twice
- Enter 9, 9, 3. The last-selected device key will blink twice
- Press VOL+ once. The last-selected device key will blink four times
- On the remote control, press and hold SETUP until the last-selected device key blinks
twice
- Enter 9, 9, 3. The last-selected device key will blink
twice
- Select a mode (e.g., TV or AUD) which you want to use to control the volume. The selected device key will blink
twice
Now, when you press VOL+, VOL-,or MUTE, the volume of the selected device (e.g., TV) is controlled regardless of mode
Volume Lock allows you to control the volume through the device identified as having your primary speaker(s), regardless of which mode you are using. On the Atlas OCAP 5-Device Remote Control, Global Volume Lock is set to TV, so you can control TV volume while in the VCR, DVD, TV or CBL mode. You can perform Individual Volume Unlock on a selected device to set its volume control for independent operation.
NOTE: The audio mode’s (AUD) volume controls are active regardless of Volume Lock settings. However, if you lock the volume controls to the AUD mode, you will have control of the audio device’s volume in all other modes (i.e., VCR, DVD, TV, and CBL). This can be an advantage if, for example, you always listen to home entertainment devices through your receiver’s speakers.Unlocking Volume Control for a Single Device (Individual Volume Unlock)
Unlocking All Volume Control (Global Volume Unlock)
NOTE: Performing these instructions will set independent volume control for all programmed devices.Locking Volume Control To One Mode (Global Volume Lock)
NOTE: The audio mode’s volume controls are active regardless of Volume Lock settings. However, if you lock the volume controls to the AUD mode, you will control the audio device’s volume in all other modes (i.e., VCR, DVD, TV, or CBL). This can be an advantage if, for example, you always listen to home entertainment devices through your receiver’s speakers.Cable ID Lock
- Turn on the cable converter
- On the remote control, press CBL once; it will blink once. Then press and hold
SETUP until the CBL key blinks twice
- Enter 9, 8, 2. The CBL key will blink four times, indicating ID Lock is
unlocked
- Perform the instructions under “Programming Device
Control” to program device control for the desired cable converter or satellite receiver. When you are done, perform steps
below to again lock the cable ID Lock
- On the remote control, press CBL once; it will blink once. Then press and hold
SETUP until the CBL key blinks twice
- Enter 9, 8, 2. The CBL key will blink twice, indicating ID Lock is again locked
The Atlas OCAP 5-Device Remote Control is locked at the factory to operate your cable provider’s set top box. However, if you have another brand or model of cable converter or satellite service that you would like to control, then you’ll need to perform the following steps to unlock the ID Lock, enter a new manufacturer’s code, and lock the ID Lock againMacro Keys
- On the remote control, press and hold SETUP until it blinks
twice
- Enter 9, 9, 5. The SETUP key blinks
twice
- Select a macro key (for example, F1) and press it
once
- Press the key sequence you want to program into the macro. For example, to turn on your TV and raise its volume, press TV followed by
VOL+
NOTE: You can program up to 15 key presses into one macro
- Press and hold SETUP until it blinks twice
- To add another macro, repeat steps 1 through 5, substituting the new key sequence to be added in step 4.
NOTE: Programming more than five macros on the same macro key overwrites previous settings. - On the remote control, press and hold SETUP until it blinks
twice
- Enter 9, 9, 5. The SETUP key blinks
twice
- Press the macro key you want to clear once
- Press and hold SETUP until it blinks twice
This macro key is now clear and ready for reprogramming.
The Atlas OCAP 5-Device Remote Control includes two macro keys (located directly below the MUTE and LAST keys). Macro keys allow you to set up key macros to activate certain keys in a specific order.For example, you can set up a key macro to change the channels on your TV, raise or lower the volume, and start recording on your VCR, all with the touch of one key. If you want to change the macros stored in a previously-programmed macro key, you’ll need to clear the key first (see “Clearing a Macro Key”.
Programming a Macro Key
Clearing a Macro Key
Master Power Key
- On the remote control, press and hold SETUP until the last-selected device key blinks
twice
- Enter 9, 9, 5. The last-selected device key blinks
twice
- Press PWR once
- For the first device you want in the power on sequence, press a device key (e.g.,
CBL) once. Then press PWR once. For the second device in the power sequence, press its key once (e.g,
TV). Then press PWR
- Repeat step 4 up to four more times to add the second, third, fourth, and fifth device, as
desired
- To save the settings and exit the program:
- Press CBL once.
- Press and hold SETUP until the CBL key blinks twice.
- After programming, point the remote control at the devices. Press
CBL once
- Press PWR once to sequentially turn the programmed home entertainment devices on or
off
You will see the devices turn on or off according to the programmed sequence - On the remote control, press and hold SETUP until the last-selected device key blinks
twice
- Enter 9, 9, 5. The last-selected device key blinks
twice
- Press and release PWR
- Press and hold SETUP until the CBL key blinks twice
The Atlas OCAP 5-Device Remote Control has a unique feature that allows you to sequentially turn up to five of your home entertainment devices on or off with a single key press.
NOTE: MASTER POWER (PWR) only works in the CBL mode. If it is not programmed, only the cable converter will turn on or off. In any other mode, pressing MASTER POWER (PWR) once will turn the selected device on or off.
Programming the Master Power Key
Using the Master Power Key
Clearing the Master Power Key
Re-Assigning Device Keys
- On the remote control, press VCR once; it will blink once. Then press and hold
SETUP until the VCR key blinks twice
- Enter 9, 9, 2. The VCR key will blink
twice
- Press AUD once, then press VCR once. The
VCR key will blink twice
The Atlas OCAP 5-Device Remote Control can be set up to control a second device of an already-assigned type. For example, to have the unit control a TV, a Cable Converter, and two audio devices (for example, two audio receivers), re-assign the unused VCR key to operate the second audio device as follows:
NOTE: VCR is preset at the factory to control an RCA VCR. Performing the steps below will overwrite those settings.The VCR key is now ready to be programmed for your second audio device. See “Programming Device Control”. To re-assign other device keys, repeat these and substitute the key sequence using the following chart:
NOTE: Only one device can be assigned to an unused device key at a time.To Re-Assign Perform Key Sequence VCR as 2nd AUD key VCR, SETUP, 9, 9, 2, AUD, VCR VCR as 2nd TV key VCR, SETUP, 9, 9, 2, TV, VCR VCR as 2nd CBL key VCR, SETUP, 9, 9, 2, CBL, VCR VCR back to VCR VCR, SETUP, 9, 9, 2, VCR, VCR To re-assign another unused device key, substitute it for the VCR key above and then perform the sequence. For example, to re-assign an unused AUD key as a second DVD key, perform AUD, SETUP, 9, 9, 2, DVD, AUD
When a re-assignment is done, the selected device key (e.g., AUD) will blink twice to confirm your choice. At that time, you will need to program device control (see “Programming Device Control”)
Activating Backlighting (Optional Models)
- Press SETUP twice within one second. Backlighting is turned on.
- Press SETUP twice within one second. Backlighting is turned off
On some models of your Atlas OCAP 5-Device Remote Control, you can activate backlighting. Backlighting enables your remote’s keypad to remain lit for five seconds after you press any key.
To enable backlighting on a remote with that feature, perform the following step:
To disable backlighting, perform the following step:
Clearing Custom Programming
- On the remote control, press and hold SETUP until the last-selected device key blinks
twice
- Enter 9, 8, 0. The last-selected device key blinks twice, pauses, and blinks twice again to confirm that all custom programming is cleared
The Atlas OCAP 5-Device Remote Control contains a Custom Programming Reset program. You can use it to remove all custom programming, except your setup codes and reassigned device keys
IMPORTANT: Executing this program will erase all custom settings for Volume Lock, Learned Keys, Tune-In Keys, and Channel Lock. However, your device programming remains
Automatic Programming
- Turn on the device
- Pressing and hold the desired device key (AUX, AUD, VCR, CBL, DVD,
TV) until all device keys on the remote begin to flash
(approximately 3 seconds), then release the key - If the device you’re are attempting to program matches the selected device key (e.g. TV = TV key) proceed to step 5.
- If the device you’re are attempting to program does not match the selected key (e.g. a second VCR =
AUX key), locate the correct prefix code for the device you wish to program (listed below). Press and release the number key that matches the prefix
code
Prefix: Device: 0 Television 1 DVD Player, VCR, or PVR 4 Audio Device 5 Combo Units
- Press and release the POWER key. The device key will stop flashing and remain
on
- Point the remote control at the selected device
- Press and hold the ▲ key until the device turns off. While holding the
▲ key the remote will send a new code approximately once every second. The device button will blink each time a new code is sent. If you pass the code that turns off the device, press the
▼ key to return to the previous code
- When the device turns off, you have found a candidate code. Press the
POWER Key to turn device back on. Test various functions using the remote control to determine if this
code will work. If primary functions do not work, make sure the device is still on then resume SmartScan™ by pressing the
▲ key to find another device code
- Once you have found a satisfactory code, press OK to lock the code. The power of the device must be on. The device key will then flash three times. Go to section 10 to recall and record your device codes. When all the codes have been attempted the device button will flash rapidly
The SmartScan™ programming instructions can also be found on the battery cover of the remote control. SmartScan™ will allow you to easily try all the available programming codes for the selected device and find the best match. If you prefer manual programming or already have the device codes see the Manual Programming section below
Manual Programming
- Press and hold the device key to be programmed until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to
flash
- Enter the four digit code for the desired device using the number keys. After pressing the first digit, the device key should light and remain on if the programming is successful. After the last digit is pressed the device key should flash three times and turn
off
Audio Device -- >
TV/DVD & TV/VCR Combos -- >
TV -- >
VCR/DVD/PVR -- >
- Test the code by trying various functions. If the primary function keys fail to respond satisfactorily try the next code listed for the manufacturer.
If you have tried all the codes listed for the manufacturer and the device does not respond, try to program the device using Automatic Programming above
To manually set up the Enterprise to operate a device, find the manufacturer of the device in the list of manufacturers’ codes
Recalling a Device Code
- Press and hold the device key to be read until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to
flash
- Press and release the OK key. The device key flashes each of the four digits in the code. A pause separates each digit. For example, three flashes represent the number 3, and a rapid flicker represents
0. A code of 1032 will be shown as:
FLASH <pause> FLICKER <pause> FLASH, FLASH, FLASH <pause> FLASH, FLASH
Count and record the sequence of flashes to determine the four-digit code.
Use the following steps to read the code set for a device. This is useful for determining a device code that was set using Automatic Programming above
Programming Volume Control
- Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
- Press and release the VOLUME ▲ key, the CBL key will remain
on
- Press and release the VOLUME ▼ key. The CBL key will turn off when
VOLUME ▼ is pressed, and will turn on when released
- Press and release the key corresponding to the device you wish to use to control volume (TV or AUD). After you release the key, the CBL key will flash three times and turn off
- Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
- Press and release the VOLUME ▲ key. The CBL device key will stop flashing and stay
on
- Press and release the VOLUME ▼ key, and then press and release the
OK key
- After you release the OK key, the CBL device key will flash three times and turn off
By default, your Enterprise remote controls cable volume through the Cable Box, and the VCR and DVD through the Television. To allow volume control through a different device:
To return volume control to the default state:
Master Power Control
- Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
- Press and release the POWER key
- Individually press and release each device key corresponding to the components you
wish to be controlled by Master Power (starting with the cable device key).
NOTE: If no keys are pressed in this step, no change will occur
- Press and release the POWER key. The
CBL key will flash three times and turn off
- Manually turn on all devices. Then test the Master Power control by pressing the
POWER key
The Master Power function allows you to turn off and on two or more devices simultaneously with a single press of the POWER button. The following steps describe how to program the Master Power Control function:
To disable Master Power, repeat the previous steps selecting only one device for Master Power (any device can be selected). The remote will now control the power ON/OFF of each device separately.
NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER key in normal operation will cause the remote to transmit the POWER on/off commands for those devices selected during Master Power programming.
To override this and transmit a POWER on/off command for a device not included in the Master Power selection, press the DEVICE key for that device and immediately press the POWER key.
Channel Lock
- Press and hold the CBL device key until all the device keys begin to
flash (approximately 3 seconds). Release the CBL key. The CBL key will
continue to flash
- Press and release the CHANNEL ▲
key
- Press and release the CHANNEL ▼
key
- Press the OK key. The CBL device key will flash three times to confirm
Channel Lock causes channel up and down functions to always operate the settop box independent of the device (TV, CBL, VCR, DVD or AUD) currently selected. The remote comes with Channel Lock activated. If you want the remote control to operate the channel function on your TV or VCR, you will need to deactivate Channel Lock:
Repeat these steps to reactivate Channel Lock
Button Descriptions
Automatic Programming
- Turn on the device
- Pressing and hold the desired device key (AUX, AUD, VCR, CBL, DVD,
TV) until all device keys on the remote begin to flash
(approximately 3 seconds), then release the key - If the device you’re are attempting to program matches the selected device key (e.g. TV = TV key) proceed to step 5.
- If the device you’re are attempting to program does not match the selected key (e.g. a second VCR =
AUX key), locate the correct prefix code for the device you wish to program (listed below). Press and release the number key that matches the prefix
code
0 Television 1 DVD Player, VCR, or PVR 4 Audio Device 5 Combo Units
- Press and release the POWER key. The device key will stop flashing and remain
on
- Point the remote control at the selected device
- Press and hold the ▲ key until the device turns off. While holding the
▲ key the remote will send a new code approximately once every second. The device button will blink each time a new code is sent. If you pass the code that turns off the device, press the
▼ key to return to the previous code
- When the device turns off, you have found a candidate code. Press the
POWER Key to turn device back on. Test various functions using the remote control to determine if this
code will work. If primary functions do not work, make sure the device is still on then resume SmartScan™ by pressing the
▲ key to find another device code
- Once you have found a satisfactory code, press OK to lock the code. The power of the device must be on. The device key will then flash three times. Go to section 10 to recall and record your device codes. When all the codes have been attempted the device button will flash rapidly
The SmartScan™ programming instructions can also be found on the battery cover of the remote control. SmartScan™ will allow you to easily try all the available programming codes for the selected device and find the best match. If you prefer manual programming or already have the device codes see the Manual Programming section below
Manual Programming
- Press and hold the device key to be programmed until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to
flash
- Enter the four digit code for the desired device using the number keys. After pressing the first digit, the device key should light and remain on if the programming is successful. After the last digit is pressed the device key should flash three times and turn
off
Audio Device -- >
TV/DVD & TV/VCR Combos -- >
TV -- >
VCR/DVD/PVR -- >
- Test the code by trying various functions. If the primary function keys fail to respond satisfactorily try the next code listed for the manufacturer.
If you have tried all the codes listed for the manufacturer and the device does not respond, try to program the device using Automatic Programming above
To manually set up the Enterprise to operate a device, find the manufacturer of the device in the list of manufacturers’ codes
Recalling a Device Code
- Press and hold the device key to be read until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to
flash
- Press and release the OK key. The device key flashes each of the four digits in the code. A pause separates each digit. For example, three flashes represent the number 3, and a rapid flicker represents
0. A code of 1032 will be shown as:
FLASH <pause> FLICKER <pause> FLASH, FLASH, FLASH <pause> FLASH, FLASH
Count and record the sequence of flashes to determine the four-digit code.
Use the following steps to read the code set for a device. This is useful for determining a device code that was set using Automatic Programming above
Programming Volume Control
- Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
- Press and release the VOLUME ▲ key, the CBL key will remain
on
- Press and release the VOLUME ▼ key. The CBL key will turn off when
VOLUME ▼ is pressed, and will turn on when released
- Press and release the key corresponding to the device you wish to use to control volume (TV or AUD). After you release the key, the CBL key will flash three times and turn off
- Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
- Press and release the VOLUME ▲ key. The CBL device key will stop flashing and stay
on
- Press and release the VOLUME ▼ key, and then press and release the
OK key
- After you release the OK key, the CBL device key will flash three times and turn off
By default, your Enterprise remote controls cable volume through the Cable Box, and the VCR and DVD through the Television. To allow volume control through a different device:
Master Power Control
- Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
- Press and release the POWER key
- Individually press and release each device key corresponding to the components you
wish to be controlled by Master Power (starting with the cable device key).
NOTE: If no keys are pressed in this step, no change will occur
- Press and release the POWER key. The
CBL key will flash three times and turn off
- Manually turn on all devices. Then test the Master Power control by pressing the
POWER key
The Master Power function allows you to turn off and on two or more devices simultaneously with a single press of the POWER button. The following steps describe how to program the Master Power Control function:
NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER key in normal operation will cause the remote to transmit the POWER on/off commands for those devices selected during Master Power programming.
To override this and transmit a POWER on/off command for a device not included in the Master Power selection, press the DEVICE key for that device and immediately press the POWER key.Channel Lock
- Press and hold the CBL device key until all the device keys begin to
flash (approximately 3 seconds). Release the CBL key. The CBL key will
continue to flash
- Press and release the CHANNEL ▲
key
- Press and release the CHANNEL ▼
key
- Press the OK key. The CBL device key will flash three times to confirm
Channel Lock causes channel up and down functions to always operate the settop box independent of the device (TV, CBL, VCR, DVD or AUD) currently selected. The remote comes with Channel Lock activated. If you want the remote control to operate the channel function on your TV or VCR, you will need to deactivate Channel Lock:
Button Descriptions
Automatic Programming
- Turn on the device
- Pressing and hold the desired device key (AUX, AUD, VCR, CBL, DVD,
TV) until all device keys on the remote begin to flash
(approximately 3 seconds), then release the key - If the device you’re are attempting to program matches the selected device key (e.g. TV = TV key) proceed to step 5.
- If the device you’re are attempting to program does not match the selected key (e.g. a second VCR =
AUX key), locate the correct prefix code for the device you wish to program (listed below). Press and release the number key that matches the prefix
code
Prefix: Device: 0 Television 1 DVD Player, VCR, or PVR 4 Audio Devices 5 Combo Units
- Press and release the POWER key. The device key will stop flashing and remain
on
- Point the remote control at the selected device
- Press and hold the ▲ key until the device turns off. While holding the
▲ key the remote will send a new code approximately once every second. The device button will blink each time a new code is sent. If you pass the code that turns off the device, press the
▼ key to return to the previous code
- When the device turns off, you have found a candidate code. Press the
POWER Key to turn device back on. Test various functions using the remote control to determine if this
code will work. If primary functions do not work, make sure the device is still on then resume SmartScan™ by pressing the
▲ key to find another device code
- Once you have found a satisfactory code, press OK to lock the code. The power of the device must be on. The device key will then flash three times. Go to section 10 to recall and record your device codes. When all the codes have been attempted the device button will flash rapidly
The SmartScan™ programming instructions can also be found on the battery cover of the remote control. SmartScan™ will allow you to easily try all the available programming codes for the selected device and find the best match. If you prefer manual programming or already have the device codes see the Manual Programming section below
Manual Programming
- Press and hold the device key to be programmed until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to
flash
- Enter the four digit code for the desired device using the number keys. After pressing the first digit, the device key should light and remain on if the programming is successful. After the last digit is pressed the device key should flash three times and turn
off
Audio Device -- >
TV/DVD & TV/VCR Combos -- >
TV -- >
VCR/DVD/PVR -- >
- Test the code by trying various functions. If the primary function keys fail to respond satisfactorily try the next code listed for the manufacturer.
If you have tried all the codes listed for the manufacturer and the device does not respond, try to program the device using Automatic Programming above
To manually set up the Enterprise to operate a device, find the manufacturer of the device in the list of manufacturers’ codes
Recalling a Device Code
- Press and hold the device key to be read until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to
flash
- Press and release the OK key. The device key flashes each of the four digits in the code. A pause separates each digit. For example, three flashes represent the number 3, and a rapid flicker represents
0. A code of 1032 will be shown as:
FLASH <pause> FLICKER <pause> FLASH, FLASH, FLASH <pause> FLASH, FLASH
Count and record the sequence of flashes to determine the four-digit code.
Use the following steps to read the code set for a device. This is useful for determining a device code that was set using Automatic Programming above
Programming Volume Control
- Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
- Press and release the VOLUME ▲ key, the CBL key will remain
on
- Press and release the VOLUME ▼ key. The CBL key will turn off when
VOLUME ▼ is pressed, and will turn on when released
- Press and release the key corresponding to the device you wish to use to control volume (TV or AUD). After you release the key, the CBL key will flash three times and turn off
- Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
- Press and release the VOLUME ▲ key. The CBL device key will stop flashing and stay
on
- Press and release the VOLUME ▼ key, and then press and release the
OK key
- After you release the OK key, the CBL device key will flash three times and turn off
By default, your Enterprise remote controls cable volume through the Cable Box, and the VCR and DVD through the Television. To allow volume control through a different device:
Master Power Control
- Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
- Press and release the POWER key
- Individually press and release each device key corresponding to the components you
wish to be controlled by Master Power (starting with the cable device key).
NOTE: If no keys are pressed in this step, no change will occur
- Press and release the POWER key. The
CBL key will flash three times and turn off
- Manually turn on all devices. Then test the Master Power control by pressing the
POWER key
The Master Power function allows you to turn off and on two or more devices simultaneously with a single press of the POWER button. The following steps describe how to program the Master Power Control function:
NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER key in normal operation will cause the remote to transmit the POWER on/off commands for those devices selected during Master Power programming.
To override this and transmit a POWER on/off command for a device not included in the Master Power selection, press the DEVICE key for that device and immediately press the POWER key.Channel Lock
- Press and hold the CBL device key until all the device keys begin to
flash (approximately 3 seconds). Release the CBL key. The CBL key will
continue to flash
- Press and release the CHANNEL ▲
key
- Press and release the CHANNEL ▼
key
- Press the OK key. The CBL device key will flash three times to confirm
Channel Lock causes channel up and down functions to always operate the settop box independent of the device (TV, CBL, VCR, DVD or AUD) currently selected. The remote comes with Channel Lock activated. If you want the remote control to operate the channel function on your TV or VCR, you will need to deactivate Channel Lock:
Button Descriptions
What Devices Can I Control?
- CBL ... cable boxes, HDTV tuners, and satellite devices
- TV ... TVs and HDTVs
- VCR ... VCRs, digital video recorders (DVRs), DVD players, and CD players
- DVD ... DVD players, CD players, VCRs, and DVRs
- AUX ... receivers, tuners, and Home Theatre
Each mode key is associated with different groups of devices. You can use each mode key to control one of its associated devices:
Programming Devices to the Remote
- Turn on the device
- Press and hold SELECT and the appropriate mode key
(CBL, TV, VCR, DVD, AUX) until all of the mode keys blink twice.
- Enter in the code for the device:
CBL Group --- Cable Box ►►
TV Group --- TV ►►
TV Group --- HDTV ►►
VCR Group --- VCR ►►
VCR Group --- DVR ►►
DVD Group --- DVD player ►►
DVD Group --- CD player ►►
AUX Group --- Receiver/Tuner ►►
AUX Group --- Home Theatre ►►
The mode keys should then blink twice if the code was accepted
- Point the remote at the device, and press POWER, PLAY,
CH▲ or CH▼ to test the device. If the device responds, you are done.
- If the device does not respond, repeat steps 2-4 for other codes (if
applicable)
- Still not successful? Try Searching for the Code (below)
Searching for the code
- Turn on the device
- Press and hold SELECT and the appropriate mode key
(CBL, TV, VCR, DVD, or AUX) until the mode keys blink
twice
- Press 9, 9, 1. The mode key you selected in step 2 blinks
twice
- Point the remote toward the device, and press PLAY . The remote automatically tests each code in its library, beginning with the most common codes. The mode key blinks once each time the remote transmits a new code*. The mode key blinks twice when it reaches the last
code
*Depending the the mode key, the remote will check through a certain amount of codes:
- CBL mode: 23
- TV mode: 225
- DVD mode: 206
- VCR mode: 210
-
AUX mode: 38
- As soon as the device powers off, press SELECT
- Verify the new code is correct by pressing POWER
- If the device powers on again, press SELECT to assign the code. If not complete the following steps:
- Turn the device on
- Press CH▲ or CH▼ to step forward or back to the correct code
- When the device turns off, press SELECT to assign the code
Find Your Code
- Press and hold SELECT and the appropriate mode key
(CBL, TV, VCR, DVD, or AUX) until all mode keys blink
twice
- Press 9, 9, 0. The mode key you selected in step 1 blinks
twice
-
Press 1 and then count the number of times the mode key blinks. The number of blinks indicates the first digit in the
code
-
For example, 4 blinks indicates the first digit in the code is 4. If the mode key does not blink, the digit is 0.
-
For example, 4 blinks indicates the first digit in the code is 4. If the mode key does not blink, the digit is 0.
-
Press 2 and then count the number of times the mode key blinks. This number indicates the second number in the
code
-
Press 3 and then count the number of times the mode key blinks. This number indicates the third number in the
code
-
Press 4 and then count the number of times the mode key blinks. This number indicates the fourth number in the
code
- After all four numbers in the code are identified, all mode keys blink three times
Find out which code programmed the mode key to control your deviceControlling POWER key for Multiple Devices at Once
- Press and hold the SELECT and CBL keys until the mode keys blink
twice
- Using the remote keypad, press 9, 9, 8. The
CBL key blinks
twice
- Press the mode key (CBL, TV, VCR, DVD, or
AUX) for the first device in the group of devices you want to power on and off at once. The
CBL key blinks twice
- Press the mode key for the second device in the group of devices you want to power on and off at once. The
CBL key blinks twice
- Repeat step for additional devices
- When done, press SELECT to save your power settings. All mode keys blink three times
- Press and hold SELECT and CBL until all mode keys blink
twice
- Press 9, 9, 8. The CBL key blinks
twice
- Press SELECT to save your power settings. All mode keys blink three times
- The POWER key will only control the device/mode the remote is in
The Remote's POWER key can turn on/off multiple devices at once, rather than needing to change.
Channel Control Lock
- Press and hold SELECT and CBL until all mode keys blink twice.
- Press 9, 9, 7. The CBL key blinks twice.
- Press the CBL. All mode keys blink three times.
NOTE: In AUX mode, the remote always controls channels for the AUX device
- Press and hold SELECT and CBL until all mode keys blink twice.
- Press 9, 9, 7. The CBL key blinks twice.
- Press SELECT. All mode keys blink three
times
- The channel keys will work with the mode key you select
You can lock the remote control to change channels only through the cable box, whether in CBL, VCR, DVD, or TV mode.
Volume Control
- Press and hold the SELECT and CBL keys until the mode keys blink
twice
- Press 9, 9, 3. The CBL key blinks twice
- Press TV. All mode keys blink three times
NOTE: In AUX mode, the remote always controls volume and mute for the AUX device - Press and hold the SELECT and CBL
keys until the mode keys blink twice
- Press 9, 9, 3. The CBL key blinks twice
- Press CBL. All mode keys blink three times
NOTE: In AUX mode, the remote always controls volume and mute for the AUX device - Press and hold the SELECT and CBL keys until the mode keys blink
twice
- Press 9, 9, 3. The CBL key blinks twice
- Press SELECT. All mode keys blink three times
You can lock the remote control to control volume and mute through one specific device, whether in CBL, VCR, DVD, or TV mode
To Control volume and mute through the TV only:
To Control volume and mute through the Cable Box only:
To Control volume and mute through whatever mode the remote is in:
Programming Devices into the AT8400 Remote
- Turn on the device
- Press and hold SELECT plus the appropriate device key until all mode keys blink
twice
- Enter in the code for the device:
TV -- >
VCR -- >
CBL -- >
AUX (Receiver) -- >
AUX (Amplifier) -- >
The mode keys should then blink twice if the code was accepted
- Test the device by pressing POWER. If the device responds, the program was
successful
- If the device does not respond, repeat steps 2-4 for other codes (if applicable)
Note: These instructions assume you have already selected the proper device code(s).
Programming Volume Control:
- Turn on the device
- Press and hold the SELECT and CBL keys until the mode keys blink
twice
- Using the remote keypad, press 9, 9, 3. The mode keys will blink
twice
- Press the mode key for the device you want to control the volume
- Point the remote at the device and verify the volume is being adjusted through it
Note: The default device is TV. For controlling the volume through the cable box, press the Settings button twice to go into the "General Settings" menu and make sure that the "Audio: Volume Control" setting is set to "Variable".
Programming Cable Receiver
- Press and hold the SELECT and CBL keys until the mode keys blink
twice
- Using the remote keypad, press 9, 9, 6. The mode keys will blink
twice
- Press CH - to unlock the remote
- Enter in the 4 digits to program the CBL key
Searching for Codes
- Turn on the device
- Press and hold SELECT and the appropriate mode key until the mode keys blink
twice
- Using the remote keypad, press 9, 9, 1. The mode keys will blink
twice
- Point the remote at the device and press PLAY. The remote will now automatically test
each code in its library beginning with the most common codes. The mode key will
flash twice when it reaches the end of the codes stored in its library
- As soon as the device powers down, press the SELECT key
- Verify that the code is correct by pressing the POWER key
- If the device powers on again, press the SELECT key again to lock in the
code
- If it does not, turn the device on and press CH + or CH - to step to the correct code. When the device turns off, press SELECT to lock in the code
Identifying Programmed Codes
- Press and hold the SELECT and CBL keys until the mode keys blink
twice
- Using the remote keypad, press 9, 9, 0. The mode keys will blink
twice
- Press 1 then count the number of times the mode key blinks. This will be the first
digit in the code. If the key does not blink the digit is 0
- Repeat Step 3 substituting 2, 3 and 4 to obtain the other 4 code
digits
- Write down the code for future reference
Quick Set Up Method
- Turn on the device you want to program. To program your TV, turn on the
TV
- Press and hold the [Device] key for 5 seconds until the Device LED will blink once and stays on. Continue to hold the
[Device] key and press the number key assigned to
your brand in the Quick Setup Code Table and release both [Device] key and the number key to save the code
CBL TV DVD 0 PACE DTA
1 SA/CISCO, SAMSUNG, PACE DIGITAL
2 MOTOROLA DIGITAL
3 MOTOROLA DTA
4 EVOLUTION DTA
5 CISCO IPTV
6 ADB IPTV
7 TECHNICOLOR
8 AMINO 140/540 IPTV
9 MOTOROLA IPTV0 SANYO
1 SONY
2 SAMSUNG
3 LG
4 TOSHIBA
5 PANASONIC
6 PHILIPS
7 HITACHI
8 SHARP
9 VIZIO0 HITACHI
1 SONY
2 PHILIPS
3 SAMSUNG
4 PHILIPS MAGNAVOX
5 PANASONIC
6 LG
7 JVC
8 DENON
9 PIONEER
- Point the remote control at the device
- Press the power button. If it turns off, it is programmed for your component. If it does not turn off, use the Pre-Programmed 3-Digit code Method or Scanning Method. Repeat the steps above for all devices (CBL, TV, DVD)
Manual Programming
- Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD)
- Press the [Device] button and the [OK/SEL] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is
on
- Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns
off
Cable Converter- [CBL] ► Cable IPTV - [CBL] ► TV - [TV] ► DVD - [DVD] ► PVR/DVR (TiVo)>- [DVD] ►
- You can verify that you have selected the correct code by pressing
[POWER]. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from
step 3 using the next three digit code number from the brand
list
- You can verify that you have selected the correct code by pressing
[POWER]. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from
step 3 using the next three digit code number from the brand
list
- Store the three-digit code by pressing the same [Device] button once again. The device LED will blink twice to confirm that the code has been stored.
The remote control can be programmed by entering a three-digit code number that corresponds to particular brands and models of equipment
Auto Search Method
- Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD)
- Press the [Device] button and [OK/SEL] simultaneously for three seconds
The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on
- Press [CH▲] or [CH▼] one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release
[CH▲] or [CH▼] as soon as the equipment turns
off
You can verify that you have selected the correct code by pressing [POWER]. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 to continue the Auto Search Method
- Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored.
If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps:Code Number Readback
- Press
the [Device] button and [SELECT] simultaneously for 3 seconds
- The device LED will light on for 20 seconds. The next step must be entered while LED is on
- Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
- Each digit is separated by 1 second. Ten blinks is equal to the number 0
- For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
This is useful for determining a device code that was set using the Auto Search Method above
Programming a Second TV to DVD key
- Press [DVD] and [SELECT]
simultaneously for 3 seconds.
- The device LED will light on for 30 seconds.
The next step must be entered while LED is on
- The device LED will light on for 30 seconds.
The next step must be entered while LED is on
- Press [TV]
- Point the remote control toward the equipment and
enter the three-digit code number assigned to your TV brand from the
code tables. The equipment will turn off when the correct three-digit
code number has been entered.
TV -- >
- Press [DVD] once again. The device LED will blink twice to confirm that the code has been stored
The Learning Method
- Press the [Device] button (CBL, TV or DVD) to be programmed and the
[INPUT] buttons simultaneously for 3 seconds until the Device LED light turns
on
- Line up the UR3L-SR4 to the other remote, head-to-head, 1 or 2 inches
apart
- Press any button on the UR3LSR4 that you want to teach a command to. For example, if you want to teach the
[MUTE] button, press the [MUTE] button
- Press and hold the [MUTE] button on the other remote until the
UR3L-SR4 Device LED light blinks twice
The LED will blink 5 times if there was an error in the learning process. In so, repeat STEPS 3 and 4. Continue learning other buttons by repeating STEPS 3 and
4
- Once you have completed teaching UR3L-SR4 all desired commands for that Device, save the learned commands by pressing the [Device] and
[INPUT] buttons simultaneously until the Device LED blinks 3 times. Now test all the buttons to make sure they learned
correctly
- Press the [Device] and [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on
- Press and hold the button you want to erase for 3 seconds. The Device LED will blink twice to confirm the erasure
- To exit, press and hold both the [Device] and [INPUT] buttons simultaneously until the Device LED blinks 3 times
- Press the [Device] and [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on
- Press and hold both the [Device] button you want to erase and the
[PAUSE] button for 5 seconds. The Device LED will blink twice to confirm the erasure
- To exit, press and hold both the [Device] and [INPUT] buttons simultaneously until the Device LED blinks 3 times
Programming the 'All Off' Button
- Press [CBL]
- Press [All OFF] and [SELECT] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
- Press the first [Device] button you want to store and then the
[POWER] button
- Press the second [Device] button you want to store and then the
[POWER] button
- Press the third [Device] button you want to store and then the
[POWER] button
- Press [CH▲] to save the power commands you stored. The [CBL] button will blink twice to confirm
This allows you to program the [All OFF] button so it can send up to three power On/Off commands with one button press
Volume Control
- Press the [OK/SEL] button and [CBL] button simultaneously for three seconds.
The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
- Press the [VOL▲] button. The device LED will blink
- Press [CBL] button. The device LED will blink twice to confirm the programming
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV TV : TV DVD : TV
If you wish to store the Cable volume control in CBL mode, use the following steps
Programming Channel Control
- Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
- Press the [VOL▼ ] button. The device LED will blink
- Press [TV] button. The device LED will blink twice to confirm the programming
Channel controls are factory-programmed to automatically transfer to the respective Device mode you select, as follows:CBL : CBL TV : CBL DVD : DVD
If you wish to store the TV channel controls in TV mode, use the following steps.Low Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [Device] button is pressed to turn on equipment.Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.Button Descriptions
Three-Digit Code Programming Method
- Turn on the device you want to program (TV,
DVD or AUX)
- Press the [DEVICE] button (TV, DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3 seconds. The device LED will light for
30 seconds indicating the unit is ready to be programmed
- Point the remote control toward the device and enter the 3-digit code number assigned to your
brand
TV ►
VCR (use VCR key) ►
TV/VCR (use VCR key) ►
DVD (use DVD key) ►
TV/DVD Combos (use DVD key) ►
TV/DVD/VCR Combos (use DVD key) ►
DVD/VCR Combos (use DVD key) ►
DVD Recorders (use DVD key) ►
Audio Device (use AUX key) ►
TiVo (use AUX key) ►
- If the 3-digit code number you just entered is correct, the
device will turn Off
- If it did not turn Off, continue entering code numbers listed for that brand until the
device turns Off
- If the 3-digit code number you just entered is correct, the
device will turn Off
- After you’ve entered the correct code number and the
device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all
work
- If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
- Once you have found the correct 3-digit code, save it by pressing the same [DEVICE] button one more time. The [DEVICE] LED light will blink twice to confirm that the code was successfully stored
Auto Search Method
- Turn on the equipment you wish to operate
- Press the [DEVICE] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
- The device LED will light on for 30 seconds. The next step must be entered while LED is on
- The device LED will light on for 30 seconds. The next step must be entered while LED is on
- Press the [CH▲] or [CH▼] button one step at a time or keep it
pressed. The remote will emit a series of Power ON/OFF commands. Release the
[CH▲] or [CH▼] button as soon as the equipment turns off.
- Verify that you selected the correct code by pressing
[POWER] again. The equipment should either turn on or turn off
- Press the [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:
Code Number Readback
- Press the [DEVICE] button and [OK/SEL] simultaneously for 3 seconds
The device LED will light on for 30 seconds. The next step must be entered while LED is on
- Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
- Each digit is separated by 1 second. Ten blinks is equal to the number 0
- For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a 5th Device to AUX Button
- Turn on the equipment you wish to operate.
- Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
- The device LED will light on for 20 seconds. The next step must be entered while LED is on
- The device LED will light on for 20 seconds. The next step must be entered while LED is on
- Press the desired [DEVICE] button. Point the remote control toward the
device and enter the 3-digit code number assigned to your brand
TV ►
VCR (use VCR key) ►
TV/VCR (use VCR key) ►
DVD (use DVD key) ►
TV/DVD Combos (use DVD key) ►
TV/DVD/VCR Combos (use DVD key) ►
DVD/VCR Combos (use DVD key) ►
DVD Recorders (use DVD key) ►
Audio Device (use AUX key) ►
TiVo (use AUX key) ►
- If the 3-digit code number you just entered is the correct number, the
device will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the
device turns
Off
- Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new
code
- Press [AUX] one more time. The desired [DEVICE] LED light will blink twice to confirm the code was stored
You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio ComponentProgramming the System On/Off Button
- Press [CBL]
- Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
- Press [TV]
- Press [DVD] (if adding)
- Press [VCR] (if adding)
- Press [AUX] (if adding)
- Press [CH▲] to save the power commands you stored. The [CBL] button will blink twice to confirm
The System on/off button can send out up to five power on/off commands for the devices you programmed into the remote control
Programming Channel Controls
- Press [TV] and [OK/SEL] button simultaneously for three seconds. The device LED will turn on for
30 seconds. The next step must be performed while the LED is on
- Press the [VOL▼] button. The device LED will blink
- Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3
Channel controls (CH▲, CH▼, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:CBL : CBL TV : CBL VCR : CBL DVD : DVD AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following steps
Volume Control
- Press [CBL] and [OK/SEL] simultaneously
for three
seconds
- [CBL] will turn on for 20 seconds. The next step must be performed while the LED is on
- [CBL] will turn on for 20 seconds. The next step must be performed while the LED is on
- Press the [VOL▲] button. The device LED will blink
- Press [CBL] button. The device LED will blink twice to confirm the programming
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV TV : TV DVD : TV AUX : AUX
If you wish to store the Cable volume control in CBL mode, use the following steps
Macro key(s)
- Press the [CBL] button to select the CBL mode
- Press the [Macro] button and [OK/SEL] button simultaneously for 3 seconds. The
[CBL] device LED will turn on for 20 seconds
- Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered
- Press the [CH▲] button to store the functions that were selected. The [CBL] device LED will blink twice to confirm the storage of functions
In the CBL mode, the M1, M2, and Help buttons can be programmed to act as a macro or favorite channel button. You can send out up to ten commands with one button press
Low Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.Button Functions
Three-Digit Code Programming Method
- Turn on the device you want to program (TV,
DVD or AUX)
- Press the [Device] button (TV, DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3 seconds. The device LED will light for
30 seconds indicating the unit is ready to be programmed
- Point the remote control toward the device and enter the 3-digit code number assigned to your
brand
TV ►
VCR (use VCR key) ►
TV/VCR (use VCR key) ►
DVD (use DVD key) ►
TV/DVD Combos (use DVD key) ►
TV/DVD/VCR Combos (use DVD key) ►
DVD/VCR Combos (use DVD key) ►
DVD Recorders (use DVD key) ►
Audio Device (use AUX key) ►
TiVo (use AUX key) ►
- If the 3-digit code number you just entered is correct, the
device will turn Off
- If it did not turn Off, continue entering code numbers listed for that brand until the
device turns Off
- If the 3-digit code number you just entered is correct, the
device will turn Off
- After you’ve entered the correct code number and the
device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all
work
- If any of the functions do not work as they should, repeat from
step 3 using the next 3-digit code number listed for that brand
- Once you have found the correct 3-digit code, save it by pressing the same [DEVICE] button one more time. The [Device] LED light will blink twice to confirm that the code was successfully stored
Auto Search Method
- Turn on the equipment you wish to operate
- Press the [Device] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
- The device LED will light on for 30 seconds. The next step must be entered while LED is on
- The device LED will light on for 30 seconds. The next step must be entered while LED is on
- Press the [CH▲] or [CH▼] button one step at a time or keep it
pressed. The remote will emit a series of Power ON/OFF commands. Release the
[CH▲] or [CH▼] button as soon as the equipment turns off.
- Verify that you selected the correct code by pressing
[POWER] again. The equipment should either turn on or turn off
- Press the [Device] button to store the code. The Device LED will blink twice to confirm that the code has been stored
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:
Code Number Readback
- Press the [Device] button and [OK/SEL] simultaneously for 3 seconds
The device LED will light on for 30 seconds. The next step must be entered while LED is on
- Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
- Each digit is separated by 1 second. Ten blinks is equal to the number 0
- For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a 5th Device to AUX Button
- Turn on the equipment you wish to operate.
- Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
- The device LED will light on for 20 seconds. The next step must be entered while LED is on
- The device LED will light on for 20 seconds. The next step must be entered while LED is on
- Press the desired [Device] button. Point the remote control toward the
device and enter the 3-digit code number assigned to your brand
TV ►
VCR (use VCR key) ►
TV/VCR (use VCR key) ►
DVD (use DVD key) ►
TV/DVD Combos (use DVD key) ►
TV/DVD/VCR Combos (use DVD key) ►
DVD/VCR Combos (use DVD key) ►
DVD Recorders (use DVD key) ►
Audio Device (use AUX key) ►
TiVo (use AUX key) ►
- If the 3-digit code number you just entered is the correct number, the
device will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the
device turns
Off
- Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new
code
- Press [AUX] one more time. The desired [Device] LED light will blink twice to confirm the code was stored
You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio ComponentProgramming the System On/Off Button
- Press [CBL]
- Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
- Press [TV]
- Press [DVD] (if adding)
- Press [VCR] (if adding)
- Press [AUX] (if adding)
- Press [CH▲] to save the power commands you stored. The [CBL] button will blink twice to confirm
The System on/off button can send out up to five power on/off commands for the devices you programmed into the remote control
Programming Channel Controls
- Press [TV] and [OK/SEL] button simultaneously for three seconds. The device LED will turn on for
30 seconds. The next step must be performed while the LED is on
- Press the [VOL▼] button. The device LED will blink
- Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3
Channel controls (CH▲, CH▼, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:CBL : CBL TV : CBL VCR : CBL DVD : DVD AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following steps
Volume Control
- Press [CBL] and [OK/SEL] simultaneously
for three
seconds
- [CBL] will turn on for 20 seconds. The next step must be performed while the LED is on
- [CBL] will turn on for 20 seconds. The next step must be performed while the LED is on
- Press the [VOL▲] button. The device LED will blink
- Press [CBL] button. The device LED will blink twice to confirm the programming
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV TV : TV DVD : TV AUX : AUX
If you wish to store the Cable volume control in CBL mode, use the following steps
Macro key(s)
- Press the [CBL] button to select the CBL mode
- Press the [Macro] button and [OK/SEL] button simultaneously for 3 seconds. The
[CBL] device LED will turn on for 20 seconds
- Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered
- Press the [CH▲] button to store the functions that were selected. The [CBL] device LED will blink twice to confirm the storage of functions
In the CBL mode, the M1, M2, Help, BLANK buttons can be programmed to act as a macro or favorite channel button. You can send out up to ten commands with one button press
Low Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.Button Functions
Three-Digit Code Programming Method
- Turn on the device you want to program (TV,
DVD, VCR or AUX)
- Press the [Device] button (TV, DVD, VCR or AUX) to be programmed and
[OK/SEL] button simultaneously for 3 seconds. The device LED will light for 30 seconds indicating the unit is ready to be programmed
- Point the remote control toward the device and enter the 3-digit code number assigned to your
brand
TV -- >
VCR (use VCR key) -- >
TV/VCR Combos (use VCR key) -- >
DVD (use DVD key) -- >
DVD Recorders (use DVD key) -- >
TV/DVD Combos (use DVD key) -- >
TV/DVD/VCR Combos (use DVD key) -- >
DVD/VCR Combos (use DVD key) -- >
Audio Device (use AUX key) -- >
TiVo (use AUX key) -- >
- If the 3-digit code number you just entered is correct, the
device will turn Off
- If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off
- If the 3-digit code number you just entered is correct, the
device will turn Off
- After you’ve entered the correct code number and the
device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all
work
- If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
- Once you have found the correct 3-digit code, save it by pressing the same
[Device] button one more
time
- The [Device] LED light will blink twice to confirm that the code was successfully stored
Auto Search Method
- Turn on the equipment you wish to operate
- Press the [Device] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
- The device LED will light on for 30 seconds. The next step must be entered while LED is on
- The device LED will light on for 30 seconds. The next step must be entered while LED is on
- Press the [CH▲] or [CH▼] button one step at a time or keep it
pressed. The remote will emit a series of Power ON/OFF commands. Release the
[CH▲] or [CH▼] button as soon as the equipment turns off.
- Verify that you selected the correct code by pressing
[POWER] again. The equipment should either turn on or turn off
- Press the [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:
Code Number Readback
- Press the [Device] button and [OK/SEL] simultaneously for 3 seconds
- The device LED will light on for 30 seconds. The next step must be entered while LED is on
- Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
- Each digit is separated by 1 second. Ten blinks is equal to the number 0
- For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
The Learning Method
- Press the [Device] button (AUX, TV, VCR or DVD) to be programmed and the
[ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns
on
- Line up the CLIKR-5 to the other remote, head-to-head, 1 or 2 inches
apart
- Press any button on the CLIKR-5 that you want to teach a command to. For example, if you want to teach the
[MUTE] button, press the [MUTE] button
- Press and hold the [MUTE] button on the other remote until the
CLIKR-5 Device LED light blinks twice
The LED will blink 5 times if there was an error in the learning process. In so, repeat STEPS 3 and 4. Continue learning other buttons by repeating STEPS 3 and 4
- Once you have completed teaching CLIKR-5 all desired commands for that Device, save the learned commands by pressing the [Device] and
[ASPECT] buttons simultaneously until the Device LED blinks 3 times. Now test all the buttons to make sure they learned
correctly
- Press the [Device] and [ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns on
- Press and hold the button you want to erase for 3 seconds. The Device LED will blink twice to confirm the erasure
- To exit, press and hold both the [Device] and [ASPECT] buttons simultaneously until the Device LED blinks 3 times
- Press the [Device] and [ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns on
- Press and hold both the [Device] button you want to erase and the
[PAUSE] button for 5 seconds. The Device LED will blink twice to confirm the erasure
- To exit, press and hold both the [Device] and [ASPECT] buttons simultaneously until the Device LED blinks 3 times
Erasing a Single Learned Command
Erasing All Learned Commands from One Device
Programming a 5th Device to AUX Button
- Turn on the equipment you wish to operate
- Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
- The device LED will light on for 30 seconds. The next step must be entered while LED is on
- The device LED will light on for 30 seconds. The next step must be entered while LED is on
- Press the [Device] button you want to setup. Point the remote control toward the
Device and enter the 3-digit code number assigned to your brand
TV -- >
VCR (use VCR key) -- >
TV/VCR Combos (use VCR key) -- >
DVD (use DVD key) -- >
DVD Recorders (use DVD key) -- >
TV/DVD Combos (use DVD key) -- >
TV/DVD/VCR Combos (use DVD key) -- >
DVD/VCR Combos (use DVD key) -- >
Audio Device (use AUX key) -- >
TiVo (use AUX key) -- >
- If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns
Off
- Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code.
- Press [AUX] one more time. The Component LED light will blink twice to confirm the code was stored
You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio ComponentProgramming the System On/Off Button
- Press [CBL]
- Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
- Press [TV]
- Press [DVD] (if adding)
- Press [VCR] (if adding)
- Press [AUX] (if adding)
- Press [CH▲] to save the power commands you stored. The [CBL] button will blink twice to confirm
The System on/off button can send out up to three power on/off commands for the devices you programmed into the remote control
Programming Channel Controls
- Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for
30 seconds. The next step must be performed while the LED is on
- Press the [VOL▼] button. The device LED will blink
- Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3
Channel controls (CH▲, CH▼, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:CBL : CBL TV : CBL VCR : CBL DVD : DVD AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following steps
Volume Control
- Press [CBL] button and [OK/SEL] simultaneously
for three
seconds
- The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
- The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
- Press the [VOL▲] button. The device LED will blink
- Press [TV] button. The device LED will blink twice to confirm the programming
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : CBL TV : TV VCR : TV DVD : TV AUX : AUX
If you wish to store the TV volume control in CBL mode, use the following steps
To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [TV] with [CBL] in Step 3
Macro (blank) Button
- Press the [CBL] button to select the CBL
mode
- Press the [MACRO] button and [OK/SEL] button simultaneously for 3 seconds. The
[CBL] button will turn on for 20 seconds
- The [MACRO] button will turn on for 30 seconds. The next step must be performed while the LED is
on
- The [MACRO] button will turn on for 30 seconds. The next step must be performed while the LED is
on
- Enter the the 2, 3 or 4-digit code for the channel you want programmed first (for example,
0-0-7) using the Number Pad, then press the [STOP] button. Then enter the code for the next channel (for example,
0-5-0), then press the [STOP] button. Repeat this process for the third channel. The
[CBL] button will blink once for each channel entered
- Press the [CH▲] button to store the
commands that were selected. The
[CBL] button will blink twice to confirm the storage of commands
- To access the programmed channels, press the [MACRO] button once. This will bring up the first channel. Press once again and it will bring up the second channel. Press again and it will bring up the third
channel
- Press the [CBL] button to select the CABLE mode
- Press a [MACRO] button and the [OK/SEL] button simultaneously for 3
seconds
- The CBL device LED will turn on for 30 seconds. The next step must be performed while the LED is
on
- The CBL device LED will turn on for 30 seconds. The next step must be performed while the LED is
on
- Press the [CH▲] button to erase the functions stored in the button. The CBL button will blink twice to confirm that the memory button has been erased
In the CABLE device mode, the two [M], [M2] buttons (see button functions below) can be programmed to act as a 'Favorite Channel' button. This allows you to program up to five 2-digit channels, four 3-digit channels or three 4-digit channels that can be accessed with one button press
To erase the Macro programming and return to the original function:
Low Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.Button Functions
Three-Digit Code Programming Method
- Turn on the device you want to program (TV,
DVD or AUX)
- Press the [Device] button (TV, DVD or AUX) to be programmed and
[SELECT] button simultaneously for 3 seconds. The device LED will light for
20 seconds indicating the unit is ready to be programmed
- Point the remote control toward the device and enter the 3-digit code number assigned to your
brand
TV ►
VCR & TV/VCR (use VCR key) ►
DVD & TV/DVD (use DVD key) ►
Audio Device (use AUX key) ►
DMX & DCR (use AUX key) ►
- If the 3-digit code number you just entered is correct, the
device will turn Off
- If it did not turn Off, continue entering code numbers listed for that brand until the
device turns Off
- If the 3-digit code number you just entered is correct, the
device will turn Off
- After you’ve entered the correct code number and the
device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all
work
- If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
- Once you have found the correct 3-digit code, save it by pressing the same [DEVICE] button one more time. The [Device] LED light will blink twice to confirm that the code was successfully stored
Auto Search Method
- Turn on the equipment you wish to operate
- Press the [Device] button and [SELECT] simultaneously for 3 seconds. The device LED will turn on
- The device LED will light on for 20 seconds. The next step must be entered while LED is on
- The device LED will light on for 20 seconds. The next step must be entered while LED is on
- Press the [CH▲] or [CH▼] button one step at a time or keep it
pressed. The remote will emit a series of Power ON/OFF commands. Release the
[CH▲] or [CH▼] button as soon as the equipment turns off.
- Verify that you selected the correct code by pressing
[POWER] again. The equipment should either turn on or turn off
- Press the [Device] button to store the code. The device LED will blink twice to confirm that the code has been stored
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:
Code Number Readback
- Press the [Device] button and [SELECT] simultaneously for 3 seconds
The device LED will light on for 30 seconds. The next step must be entered while LED is on
- Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
- Each digit is separated by 1 second. Ten blinks is equal to the number 0
- For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a Second TV to AUX Button
- Turn on the equipment you wish to operate
- Press [AUX] and [SELECT] simultaneously for 3 seconds. The device LED will turn on
- The device LED will light on for 20 seconds. The next step must be entered while LED is on
- The device LED will light on for 20 seconds. The next step must be entered while LED is on
- Press [TV]. Point the remote control toward the Component and enter the 3-digit code number assigned to your brand
TV ►
- If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns
Off
- Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new
code
- Press [AUX] one more time. The Device LED light will blink twice to confirm the code was stored
You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio ComponentProgramming the System On/Off Button
- Press [CBL]
- Press [System On/Off] and [SELECT] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
- Press [TV]
- Press [DVD] (if adding)
- Press [VCR] (if adding)
- Press [AUX] (if adding)
- Press [CH▲] to save the power commands you stored. The [CBL] button will blink twice to confirm
The System on/off button can send out up to five power on/off commands for the devices you programmed into the remote control
Programming Channel Controls
- Press [TV] and [SELECT] button simultaneously for three seconds. The device LED will turn on for
30 seconds. The next step must be performed while the LED is on
- Press the [VOL▼] button. The device LED will blink
- Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3
Channel controls (CH▲, CH▼, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:CBL : CBL TV : CBL VCR : CBL DVD : DVD AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following steps
Volume Control
- Press [CBL] and [SELECT] simultaneously
for three
seconds
- [CBL] will turn on for 20 seconds. The next step must be performed while the LED is on
- [CBL] will turn on for 20 seconds. The next step must be performed while the LED is on
- Press the [VOL▲] button. The device LED will blink
- Press [CBL] button. The device LED will blink twice to confirm the programming
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV TV : TV DVD : TV AUX : AUX
If you wish to store the Cable volume control in CBL mode, use the following steps
To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3
Programming For Advanced Function (blank key)
- Press the [CBL] button to select the CBL mode
- Press the BLANK button and [SELECT] button simultaneously for 3 seconds. The
[CBL] device LED will turn on for 20 seconds
- Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered
- Press the [CH▲] button to store the functions that were selected. The [CBL] device LED will blink twice to confirm the storage of functions
In the CBL mode, the BLANK button can be programmed to act as a macro or favorite channel button. You can send out up to ten commands with one button press
Low Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [Device] button is pressed to turn on equipment.Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.Button Functions
Quick Set-Up Method
- Turn on the device you want to program to program your TV, turn the TV
on
- Point the remote at the TV and press and hold the TV key for 3
seconds. While Holding the TV key, the TV LED will light off and on
again
- Begin to press the number keys, one at a time, starting with
1, then 2, 3, 4, 5, 6, 7, 8,
9, 0 until the TV turns off
- Release the TV key to save the code. The TV LED will blink twice to confirm the code is stored. Repeat these steps for your DVD, Aux, etc
Three-Digit Code Programming Method
- Turn on the device you want to program (TV,
DVD or AUX)
- Press the [Device] button (TV, DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3 seconds. The device LED will light for 30 seconds indicating the unit is ready to be programmed
- Point the remote control toward the device and enter the 3-digit code number assigned to your
brand
TV -- >
DVD (use DVD key) -- >DVD Recorders (use DVD key) -- >
TV/DVD Combos (use DVD key) -- >
DVD/VCR Combos (use DVD key) -- >
TV/VCR Combos (use DVD key) -- >
VCR (use DVD key) -- >
TV/DVD/VCR Combos (use DVD key) -- >
Audio Device (use AUX key) -- >
TiVo (use AUX key) -- >
iPod Controls (use AUX key) -- >
Media PCs (use AUX key) -- >
Gaming Systems (use AUX key) -- >
Lighting Controls (use AUX key) -- >
Digital to Analog Converter box (use AUX key) -- >
- If the 3-digit code number you just entered is correct, the
device will turn Off
- If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off
- If the 3-digit code number you just entered is correct, the
device will turn Off
- After you’ve entered the correct code number and the
device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all
work
- If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
- Once you have found the correct 3-digit code, save it by pressing the same [DEVICE] button one more
time
- The [Device] LED light will blink twice to confirm that the code was successfully stored
Auto Search Method
- Turn on the equipment you wish to operate
- Press the [DEVICE] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
- The device LED will light on for 30 seconds. The next step must be entered while LED is on
- The device LED will light on for 30 seconds. The next step must be entered while LED is on
- Press the [CH▲] or [CH▼] button one step at a time or keep it
pressed. The remote will emit a series of Power ON/OFF commands. Release the
[CH▲] or [CH▼] button as soon as the equipment turns off.
- Verify that you selected the correct code by pressing
[POWER] again. The equipment should either turn on or turn off
- Press the [Device] button to store the code. The Device LED will blink twice to confirm that the code has been stored
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:
Code Number Readback
- Press the [Device] button and [OK/SEL] simultaneously for 3 seconds
- The device LED will light on for 30 seconds. The next step must be entered while LED is on
- Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
- Each digit is separated by 1 second. Ten blinks is equal to the number 0
- For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a 4th Device to AUX Button
- Turn on the equipment you wish to operate
- Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
- The device LED will light on for 30 seconds. The next step must be entered while LED is on
- The device LED will light on for 30 seconds. The next step must be entered while LED is on
- Press the [Device] button you want to setup. Point the remote control toward the
Device and enter the 3-digit code number assigned to your brand
TV -- >
DVD (use DVD key) -- >DVD Recorders (use DVD key) -- >
TV/DVD Combos (use DVD key) -- >
DVD/VCR Combos (use DVD key) -- >
TV/VCR Combos (use DVD key) -- >
VCR (use DVD key) -- >
TV/DVD/VCR Combos (use DVD key) -- >
Audio Device (use AUX key) -- >
TiVo (use AUX key) -- >
iPod Controls (use AUX key) -- >
Media PCs (use AUX key) -- >
Gaming Systems (use AUX key) -- >
Lighting Controls (use AUX key) -- >
Digital to Analog Converter box (use AUX key) -- >
- If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns
Off
- Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code.
- Press [AUX] one more time. The Device LED light will blink twice to confirm the code was stored
You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio ComponentProgramming the System On/Off Button
- Press [CBL]
- Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
- Press [TV]
- Press [DVD] (if adding)
- Press [AUX] (if adding)
- Press [CH▲] to save the power commands you stored. The [CBL] button will blink twice to confirm
The System on/off button can send out up to three power on/off commands for the devices you programmed into the remote control
Programming Channel Controls
- Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for
30 seconds. The next step must be performed while the LED is on
- Press the [VOL▼] button. The device LED will blink
- Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3
Channel controls (CH▲, CH▼, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:CBL : CBL TV : CBL DVD : DVD AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following steps
Volume Control
- Press [CBL] button and [OK/SEL] simultaneously
for three
seconds
- The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
- The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
- Press the [VOL▲] button. The device LED will blink
- Press [CBL] button. The device LED will blink twice to confirm the programming
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV TV : TV DVD : TV AUX : AUX
If you wish to store the Cable volume control in CBL mode, use the following steps
To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3
Low Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.Button Functions